Yamaha FZ8NB Скачать руководство пользователя

Страница: 92 / 108

SPECIFICATIONS

9-1

Dimensions:

Overall length:

2140 mm (84.3 in)

Overall width:

770 mm (30.3 in)

Overall height:

1065 mm (41.9 in)

Seat height:

815 mm (32.1 in)

Wheelbase:

1460 mm (57.5 in)

Ground clearance:

140 mm (5.51 in)

Minimum turning radius:

3000 mm (118.1 in)

Weight:

Curb weight:

FZ8NB 212 kg (467 lb)
FZ8NBC 213 kg (470 lb)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Inline 4-cylinder

Displacement:

779 cm³

Bore

stroke:

68.0

53.6 mm (2.68

2.11 in)

Compression ratio:

12.00 : 1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

Type:

SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter cartridge replacement:

2.90 L (3.07 US qt, 2.55 Imp.qt)

With oil filter cartridge replacement:

3.10 L (3.28 US qt, 2.73 Imp.qt)

Cooling system:

Coolant reservoir capacity (up to the
maximum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

Radiator capacity (including all routes):

2.25 L (2.38 US qt, 1.98 Imp.qt)

Air filter:

Air filter element:

Oil-coated paper element

Fuel:

Recommended fuel:

Regular unleaded gasoline or gasohol
(E10)

Fuel tank capacity:

17.0 L (4.49 US gal, 3.74 Imp.gal)

Fuel reserve amount:

3.4 L (0.90 US gal, 0.75 Imp.gal)

Fuel injection:

Throttle body:

ID mark:

FZ8NB 39P1 00
FZ8NBC 39P3 10

Spark plug(s):

Manufacturer/model:

NGK/CR9E

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction ratio:

1.512 (65/43)

Final drive:

Chain

Secondary reduction ratio:

2.875 (46/16)

Transmission type:

Constant mesh 6-speed

Operation:

Left foot operation

–20 –10 0

10 20 30 40 50 ˚C

10 30 50 70 90 110

130 ˚F

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

SAE 10W-50

U39P11E0.book Page 1 Monday, August 1, 2011 5:00 PM

Содержание FZ8NB













































































































Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды

Yamaha FZ8NB, Руководство пользователя

Результаты поиска

Содержание FZ8NB

Отзывы:

Похожие инструкции для FZ8NB

Бренды по названию

Популярные бренды