Yamaha FZ8NB Скачать руководство пользователя | Manualshive

Страница: 73 / 108

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-29

7

EAU23202

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10731

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the sidestand could contact the
ground and distract the operator, re-
sulting in a possible loss of control.

EAU23272

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

WARNING! To avoid injury,

securely support the vehicle so
there is no danger of it falling
over.

[EWA10751]

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U39P11E0.book Page 29 Monday, August 1, 2011 5:00 PM

«
...
71
72
73
74
75
...
»

Содержание FZ8NB













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ8NB

Бренд: Caberg Страницы: 16

Бренд: GAS GAS Страницы: 34

Бренд: yasuni Страницы: 8

LIX9U0003740299

Бренд: X-lite Страницы: 116

Windscreen N20012A

Бренд: VStreamT Страницы: 3

Бренд: Pandora Страницы: 56

Бренд: Yamaha Страницы: 215

Бренд: Yamaha Страницы: 319

Бренд: Yamaha Страницы: 688

XMAX YP250R 2013

Бренд: Yamaha Страницы: 94

Бренд: DYNATEK Страницы: 11

Бренд: DYNATEK Страницы: 5

Бренд: Hudora Страницы: 8

Бренд: JETPRIME Страницы: 4

Бренд: LSL Страницы: 4

Бренд: BMW Motorrad Страницы: 28

Бренд: BMW Motorrad Страницы: 170

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды