Yamaha FZ6-SA Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 92

Yamaha FZ6-SA Скачать руководство пользователя страница 64

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

6

fluid and may result in vapor lock,
and dirt may clog the ABS hydrau-
lic unit valves.

●

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

●

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.

EAU22730

Changing the brake fluid

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

●

Oil seals: Replace every two
years.

●

Brake hoses: Replace every four
years.

EAU22760

Drive chain slack

The drive chain slack should be
checked before each ride and adjusted
if necessary.

EAU22791

To check the drive chain slack

1. Place the motorcycle on the cen-

terstand.

2. Shift the transmission into the neu-

tral position.

3. Spin the rear wheel several times

to locate the tightest portion of the
drive chain.

4. Measure the drive chain slack as

shown.

1. Drive chain slack

U4P5E0E0.book Page 23 Wednesday, December 14, 2005 11:15 AM

«
...
62
63
64
65
66
...
»

Содержание FZ6-SA





























































































Отзывы:

Нет отзывов