Yamaha FZ1-NW Скачать руководство пользователя страница 68

Страница: 68 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-22

3. Tighten the locknuts, then the axle

nut to their specified torques.

EAU23022

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

CAUTION:

ECA10581

The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.

1. Clean the drive chain with kero-

sene and a small soft brush.

CAUTION:

ECA11120

To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

CAUTION:

ECA11110

Do not use engine oil or any other lu-
bricants for the drive chain, as they
may contain substances that could
damage the O-rings.

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

Axle nut:

150 Nm (15.0 m·kgf, 110 ft·lbf)

U2D121E0.book Page 22 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

Содержание FZ1-NW



































































































Результаты поиска

Содержание FZ1-NW

Отзывы:

Похожие инструкции для FZ1-NW

Бренды по названию

Популярные бренды

Yamaha FZ1-NW, Руководство пользователя

Результаты поиска

Содержание FZ1-NW

Отзывы:

Похожие инструкции для FZ1-NW

Бренды по названию

Популярные бренды