Yamaha FAZER FZ6-SV 2006 Скачать руководство пользователя страница 74

Страница: 74 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

EAU25080

Rear wheel

EAU32872

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.
2. Place the motorcycle on the cen-

terstand.

3. Remove the axle nut.
4. Loosen the locknut and drive chain

adjusting nut on each side of the
swingarm.

5. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

NOTE:

The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.

6. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

NOTE:

A rubber mallet may be useful to tap the
wheel axle out.

7. Remove the wheel.

1. Axle nut
2. Drive chain slack adjusting nut

3. Locknut

1. Wheel axle

2. Drive chain slack adjusting nut
3. Locknut

4. Brake caliper bracket

5. Brake caliper

U5VX22E0.book Page 34 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

Содержание FAZER FZ6-SV 2006



























































































Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды

Yamaha FAZER FZ6-SV 2006, Руководство пользователя

Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды