Yamaha F75B Скачать руководство пользователя | Manualshive

Страница: 59 / 88

background image

Operation

53

3.

Pull the tilt support lever toward you to
support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down sud-
denly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-
sure.

[EWM00262]

NOTICE:

Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be trail-
ered in the normal running position,
use an additional support device to
secure it in the tilt position. For more
detailed information, see page 56.

[ECM01641]

4.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and

tilt switch “

” (down) to retract the trim

rods.

NOTICE:

Be sure to retract the

trim rods completely during mooring.
This protects the rods from marine
growth and corrosion which could
damage the power trim and tilt mecha-
nism.

[ECM00251]

EMU33120

Procedure for tilting down (power trim
and tilt models)

1.

Push the power trim and tilt switch “

”

(up) until the outboard motor is supported
by the tilt rod and the tilt support lever be-
comes free.

2.

Release the tilt support lever.

3.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to the
desired position.

UP

ZMU04232

DN

ZMU01936

UP

DN

U6D625E0.book Page 53 Thursday, March 13, 2008 9:06 AM

«
...
57
58
59
60
61
...
»

Содержание F75B

























































































Отзывы:

Нет отзывов

Похожие инструкции для F75B

Бренд: Acer Страницы: 2

Бренд: ON Semiconductor Страницы: 20

Бренд: EPOX Страницы: 83

Analog Devices DC2605A

Бренд: Linear Страницы: 16

KEEX-1850 Series

Бренд: Quanmax Страницы: 61

Бренд: Intel Страницы: 97

Бренд: Gigabyte Страницы: 36

Бренд: Microchip Technology Страницы: 52

Бренд: Fairchild Страницы: 17

Kontron pITX-iMX8M

Бренд: S&T Страницы: 65

Бренд: Commell Страницы: 53

Бренд: Texas Instruments Страницы: 20

Бренд: ASROCK Страницы: 2

Бренд: ECS Страницы: 44

Бренд: AIC Страницы: 58

Бренд: ITX SECURITY Страницы: 18

Бренд: Aura Light Страницы: 8

Бренд: ASROCK Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды