1
Introduction
Thank you very much for purchasing the DXS Powered Subwoofer. The DXS is a powered subwoofer used
for sound reinforcement and temporary installations. This owner’s manual explains how to set up and use
the subwoofer in live venues and temporary PA installations to enhance low-end sound. Be sure to read this
manual before using this subwoofer, in order to make sufficient use of the many functions that this product
offers. Also, be sure to keep this manual after you are finished reading it.
Features
High power, high sound pressure, superior low-end playback capabilities
Adopting a bandpass type enclusure for high sound pressure. The DXS features a high-resistance input,
low distortion woofer and a 1,020 W power amplifier to achieve superior low-end playback capability
and high sound pressure.
Flexible features
•
D-XSUB:
D-XSUB is a DSP technology that gives users additional dynamic control of the frequency
range to meet the demands of a variety of applications or musical styles.
•
Selectable X-OVER (80/100/120 Hz):
Selecting the cut-off frequency and LPF/HPF settings offers
users more flexibility to adapt to various applications.
•
Cardioid mode:
The Cardioid mode setting adds additional control of low frequencies for sub-woofer
arrays of two or more DXS speakers, effectively reducing the SPL of bass directed towards the stage
while increasing the bass levels directed towards the audience.
Reliability
A high-performance DSP control protects the speaker and amplifier. The DXS can be used worry-free,
even under harsh operating conditions.
Durability
The DXS’s sturdy plywood cabinet is covered with an extremely durable polyurea finish that provides
added protection from outside elements.
Fast and easy setup
M20 and Ø35 mm dual pole sockets allow for more flexible set up, while optional casters are also avail-
able for improved portability.
DXS1
8
DXS15 mkll
DXS12 mkll
POWERED SUBWOOFER
EN
ZZ20050
Owner’s Manual
• The DXS18 is mainly used for the explana-
tions in this manual.
• The illustrations as shown in this manual are
for instructional purposes only.
• The company names and product names used
in this manual are the trademarks or registered
trademarks of their respective companies.
Input the output signal from a source, such as a mixer, to the INPUT jack of the DXS, and input the output
signal from the OUTPUT jack of the DXS to the input jack of a full-range speaker.
• X-OVER switch (
!2
)
It is recommended that you match the crossover frequency (the cutoff frequency of the low pass filter)
of the DXS and the cutoff frequency of the high pass filter of the full-range speaker. The same fre-
quency range output from the DXS and the full-range speaker may cause interference with each other
and degrade the frequency characteristics.
• THROUGH/HPF POST switch (
o
)
If the full-range speaker is properly equipped with a high pass filter, you should set this to
[THROUGH]. The [THROUGH] setting enables you to control the level independently and minimize
signal delay. If the full-range speaker is not equipped with a high pass filter or the high pass filter in the
full-range speaker cannot be set to the same cutoff frequency as that of the low pass filter of the DXS,
set this to [HPF POST] to use the high pass filter in the DXS.
This is a pole socket used to mount a full-range speaker atop the DXS. The pole socket is compatible with
35 mm or M20 speaker poles, available commercially. When using the pole socket, be sure that the follow-
ing conditions are met.
Installing optional wheels SPW-1 at the back of the DXS enables you to transport the unit easily. To install
the wheels, use the screws already installed in the DXS unit.
Please do not use the speaker once the screws are removed. This causes air leaks to occur in enclosure,
resulting in undesirable performance.
* If any specific problem should persist, please contact your Yamaha dealer.
* The contents of this manual apply to the latest specifications as of the publishing date.
To obtain the latest manual, access the Yamaha website then download the manual file.
Basic Setup
CAUTION
If multiple powered speakers are connected in daisy-chain fashion, turn each device on
in sequence starting from the one nearest to the sound source, and turn them off start-
ing from the one farthest from the sound source.
Combination of monaural DXS and stereo full-range speakers
Combination of stereo DXS and stereo full-range speakers
NOTE
The L and R jacks are interchangeable; there is no difference in behavior between them.
Full-range
speaker
Combination and setting examples
Using the high pass filter in the
connected full-range speaker
Using the high pass filter in
the DXS
Full-range
speaker
DXS
o
!2
o
!2
From
mixer
From mixer
Full-range speaker
Full-range speaker
Mixer
To full-range speaker
DXS
Full-range speaker
Full-range speaker
Mixer
DXS
DXS
From mixer
To full-range speaker
Installing a Speaker Pole
Subwoofer
Top-mounted speaker
Pole length
DXS18
Weight 28.0 kg or less, height 76 cm or less (DSR115)
120 cm or less
DXS15mkII
Weight 19.3 kg or less, height 61 cm or less (DXR12)
100 cm or less
DXS12mkII
Weight 14.6 kg or less, height 51 cm or less (DXR10)
82 cm or less
Weight 13.5 kg or less, height 46 cm or less (DXR8)
90 cm or less
Installing Wheels
CAUTION
• For details on installing the wheels or special precautions you should take, please
refer to the relevant manual for the wheels.
• Do not install wheels other than the SPW-1.
Troubleshooting
Symptom
Possible causes
Possible solution
Power does not turn on.
The power cord is not con-
nected properly.
Connect the power cord properly.
Power suddenly turned
off.
The protection system has
been activated, shutting
down the power supply.
Turn off the power, wait until the amplifier cools down,
and then turn on again.
No sound.
The cable is not con-
nected properly.
Connect the cable to the INPUT jack properly.
Sound is interrupted
suddenly.
The protection circuit has
been activated, muting the
output.
Wait until the amplifier cools down. If the unit doesn’t
automatically reset itself, turn off the power, and then
on again.
Sound howls (feed-
back).
A microphone is directed
toward the speaker.
Keep the speaker away from the area where the
microphone picks up the sound.
The sound from each
speaker differs (if multi-
ple speakers are used.)
The settings for each
speaker differ.
Set each switch of each speaker to the same posi-
tion.
Sound is distorted.
Input volume is excessive.
Lower the volume of the input device so that the
PEAK indicator lights only occasionally.
Output volume is exces-
sive.
Lower the output level with the LEVEL control so that
the LIMIT indicator lights only occasionally.
General Specifications
General Specifications
DXS18
DXS15mkII
DXS12mkII
System Type
Powered subwoofer, band-pass type
Frequency Range (-10 dB)
32 Hz–120 Hz
40 Hz–150 Hz
42 Hz–150 Hz
Measured Maximum SPL (Peak)
Pink Noise @1m
136 dB SPL
135 dB SPL
134 dB SPL
Power
Amplifier
Power
Rating
Dynamic
1,020 W
Continuous
800 W
Power Consumption
(1/8 output power)
100 W
Components
LF
18" cone,
4" voice coil
15" cone,
2.5" voice coil
12" cone,
2.5" voice coil
Dimensions
(W × H × D; including rubber feet)
563 × 683 × 721 mm 480 × 611 × 614 mm 400 × 567 × 570 mm
Weight
49.7 kg
36.0 kg
30.0 kg
Handles
Steel, side × 2
Pole Sockets (top surface)
Ø35 mm (depth: 80 mm), M20 (threaded depth: 25 mm)
Connectors
Input
XLR3-31 × 2
Output
XLR3-32 × 2 (THROUGH or HPF POST)
Power
IEC AC inlet × 1 (V-Lock)
Input Sensitivity (LEVEL: center)
+10 dBu
Maximum Input Level
+24 dBu
M20 screw
Ø35
q
Pole sockets
Adapts to commercially available speaker poles of 35 mm diameter and
M20 screws. For details on installing speaker poles, refer to “Installing
a Speaker Pole.”
w
Feet cups
When stacking multiple DXS units, align the rubber feet of the upper
DXS unit to the feet cups of the lower.
e
Front LED
Turns on when the power is on. Lights more brightly when the output
limiter is active. Using FRONT LED DISABLE switch (
!9
) allows you
to defeat the front LED altogether.
r
Wheel mounting holes
Optional SPW-1 wheels can be installed at these locations. For details
on installing the wheels or special precautions you should take, please
refer to the relevant manual for the wheels.
t
AC IN inlet (V-Lock)
Connect the AC power cord included with the unit. The AC power cord
includes a locking mechanism with a latch. First connect the DXS to the
AC power cord, and then connect the power cord to the AC outlet.
When removing the cord, push the latch while pulling the cord out.
y
Power switch
Turns the power to the unit on ( ) or off (
).
If you are using multiple units, turn on the power to each unit one by
one. If you turn on the power to multiple units simultaneously, a tempo-
rary drop in the power voltage may occur, possibly resulting in abnor-
mal operation of the units.
Also, rapidly turning the unit on and off in succession can cause it to
malfunction. After turning the unit off, wait for about 5 seconds before
turning it on again.
u
INPUT jacks
These are balanced input XLR jacks (line-level), and this device outputs
the mixed signals of L and R.
i
OUTPUT jacks
These are balanced output XLR jacks for connecting full-range speak-
ers or additional DXS units. The output signal can be switched via the
THROUGH/HPF POST switch (
o
).
L/R output from the OUTPUT jacks correspond to L/R input to the
INPUT jacks. The mixed signal of L/R is not output.
o
THROUGH/HPF POST switch
Switches the signals output from the OUTPUT jacks (
i
).
•
THROUGH:
Outputs unaffected signals from INPUT jacks (
u
).
Select when using HPF of the connected speaker or connecting addi-
tional DXS units.
•
HPF POST:
Outputs signal input from INPUT jacks (
u
) after pass-
ing through a HPF. The cutoff frequency of the high pass filter is the
frequency specified with the X-OVER switch (
!2
). Because the out-
put level from the OUTPUT jacks is linked to the LEVEL control
(
!1
), the levels of this unit and the full-range speaker change simulta-
neously.
!0
PEAK indicator
Lights red when the input level reaches 3 dB below clipping. If the indi-
cator lights frequently, adjust the volume of the input source or lower
the LEVEL control (
!1
) so that the indicator flashes only briefly at the
highest input levels.
!1
LEVEL control
Adjusts the output level.
!2
X-OVER switch
Specifies the crossover frequency at 120 Hz, 100 Hz, or 80 Hz. The out-
put from the unit is processed through a low pass filter to cut the range
of the selected frequency or higher. When setting THROUGH/HPF
POST switch (
o
) to [HPF POST], the output signals from the OUT-
PUT jacks are processed through a high pass filter to cut the range of
the selected frequency or lower, and the crossover frequency is linked to
that of the connected speaker.
!3
D-XSUB switch
Switches the low-range frequency response characteristics.
•
NORMAL:
A generic setting corresponding to various applications.
•
BOOST:
Boosts the frequency range enhancing and providing punch
to the sound.
•
XTD LF (eXTenDed LF):
Extends the bottom of the low frequency
range.
!4
CARDIOID switch
Connection of multiple DXS units enables the use of Cardioid mode.
For details on Cardioid mode and using the switch, refer to “Setup of
Cardioid Mode” on the opposite page.
!5
POLARITY switch
Switches the polarity of the unit, normal or inverted. When the polarity
is inverted, the INVRT indicator lights.
In most cases, this should be set to normal; however, the inverted setting
may improve low-range response, depending on the type and location of
the speaker system. Select a setting that produces the best low-end
sound.
!6
LIMIT indicator
Lights when the output limiter is active. The output limiter operates in
order to protect the speaker and amplifier, attenuating the output signal
to the amplifier. If the indicator lights frequently, adjust the volume of
the input source or lower the LEVEL control (
!1
) so that the indicator
only occasionally lights at the highest input levels.
!7
PROTECTION indicator
Lights when the protection system is active. The protection system
operates and the speaker output is muted in the following situations.
• If amplifier overheating is detected.
• If overcurrent is detected.
• Immediately after turning the power on. (The protection system is
activated to prevent noise and the indicator lights for about two sec-
onds. The indicator turns off when the power supply has started nor-
mally.)
!8
POWER indicator
Lights when the power is on.
!9
FRONT LED DISABLE switch
Turns the FRONT LED at the front of the unit on or off. The LED lights
when this switch is set to off. Turn this switch on to disable the LED.
Controls and functions
t y
q
r
u
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
i
w
e
CAUTION
Do not stack more than two DXS units.
CAUTION
Turn off the power before you connect or discon-
nect the power cord.
CAUTION
A slight electrical current will flow even when the
power switch is turned off. Make sure to unplug
the power cord from the power outlet when not
using the speaker for an extended period of time.
CAUTION
Make sure to lower the input level when switching.
Included accessories
• AC power cord
• Owner’s manual (this leaflet)
• Technical Specifications
Optional accessories
• Speaker cover: SPCVR-18S01 (for DXS18), SPCVR-DXS152 (for DXS15mkII), SPCVR-DXS122 (for DXS12mkII)
• Wheels: SPW-1; 4 pieces
