Yamaha DX150A Скачать руководство пользователя | Manualshive

Страница: 65 / 123

background image

E

3-22

UP
DN

701034*

UP

DN

403033

302012

UP

DOWN

EMU01201

PROCEDURE FOR TILTING UP

Power trim/tilt model

1)

If there is a fuel joint or a fuel cock on
the boat, disconnect the fuel line or
close the fuel cock.

2)

Push the power trim/tilt switch “UP”
until the outboard has tilted up com-
pletely.

3)

Turn the tilt-support lever toward you
and support the engine.

w

After tilting the engine, be sure to sup-
port it with the tilt-support lever.
Otherwise, the engine could fall back
down suddenly if oil in the power
trim/tilt unit should lose pressure.

4)

Once the engine is supported with the
tilt-support lever, push the power
trim/tilt switch DOWN to retract the
trim rods.

c

C

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growths and corrosion
which could damage the power trim/tilt
mechanism.

67N-9-13-3 4/19/01 5:09 PM Page 23

«
...
63
64
65
66
67
...
»

Содержание DX150A




























































































































Отзывы:

Нет отзывов

Похожие инструкции для DX150A

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 19

Бренд: IEI Technology Страницы: 126

Бренд: Texas Instruments Страницы: 19

Бренд: Biostar Страницы: 27

Бренд: Texas Instruments Страницы: 23

Бренд: Texas Instruments Страницы: 18

Бренд: DFI Страницы: 60

Бренд: ECS Страницы: 93

Бренд: Texas Instruments Страницы: 13

Бренд: Intel Страницы: 78

Бренд: IBASE Technology Страницы: 56

MEG X570S UNIFY-X MAX

Бренд: MSI Страницы: 204

Бренд: Microchip Technology Страницы: 31

Бренд: Silicon Laboratories Страницы: 18

DQ963FX - Desktop Board Motherboard

Бренд: Intel Страницы: 72

TAS5508-5142K7EVM

Бренд: Texas Instruments Страницы: 20

Chipset TRF2436EVM

Бренд: Texas Instruments Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды