Yamaha DX150A Скачать руководство пользователя

Страница: 30 / 123

2-7

001082

001049

EMU01614

DIGITAL TACHOMETER

This gauge contains the tachometer, trim
meter, hour meter, oil level indicator, and
the overheat warning indicator.

Tachometer

Trim meter

Hour meter

Oil level indicator

Overheat warning indicator

Set button

Mode button

NOTE:

All segments of the display will light
momentarily after the main switch is
turned on and will return to normal there-
after.

001078

001050

EMU00136

Tachometer

This meter shows the engine speed.

EMU01109

Trim Meter

This meter shows the trim angle of your
outboard motor.

NOTE:

Memorize the trim angles that work
best for your boat under different condi-
tions. Adjust the trim angle to the
desired setting by operating the power
trim and tilt switch.

If the trim angle of your motor exceeds
the trim operating range, the top seg-
ment on the trim meter display will start
to blink.

67N-9-13-2 4/19/01 5:08 PM Page 8

Содержание DX150A




























































































































Результаты поиска

Содержание DX150A

Отзывы:

Похожие инструкции для DX150A

Бренды по названию

Популярные бренды

Yamaha DX150A, Руководство пользователя

Результаты поиска

Содержание DX150A

Отзывы:

Похожие инструкции для DX150A

Бренды по названию

Популярные бренды