background image

Setup Procedures

Verifying the Hardware Installation

After connecting the CRW8824IX drive to the computer (or an IEEE daisy-chain
or tree), you can verify that the drive is correctly recognized from your computer.

Windows Users

Make sure that the CRW8824IX is recognized by the operating system.

From the Windows 98 Second Edition’s [Start] menu, select [Settings]-[Control
Panels] and open the [System] control panel.  In the [System Properties] window,
select the [Device Manager] tab.  If you can find a new CD drive icon (YAMAHA
CRW8824E), an IEEE1394 bus controller icon, and an SBP2 icon as shown below,
you have successfully installed both the drive and the IEEE1394 interface card as
Windows OS recognizes both devices.

This screen shot is from Windows 98 Second Edition.

n

For more information about how to use the operating system, refer to the
documentation that came with it.

n

If there is a 

 mark next to the icon for the CRW8824IX drive or the IEEE1394 bus

controller, this means that it has not been installed correctly.  In either case, the
CRW8824IX drive may not work properly.

n

For Windows 2000, double-click [System] in the [Control Panels], select the
[Hardware] tab, and click the [Device Manager] button in [System Properties].

16

Содержание CRW8824IX Series













































Отзывы: