
RX-Z1/DSP-AZ1
RX-Z1/DSP-AZ1
16
• Starting DIAG in the protection cancel
mode
If the protection function works and causes hindrance to
trouble diagnosis, cancel the protection function as
described below, and it will be possible to enter the DIAG
mode. (The protection functions other than the excess
current detect function will be disabled.)
Press the “STANDBY/ON” key while simultaneously
pressing those two keys indicated in the figure on the
previous page. At this time, keep pressing those two keys
for 3 seconds or longer.
In this mode, the “SLEEP” segment of the FL display of the
main unit flashes to indicate that the mode is DIAG mode
with the protection functions disabled.
CAUTION!
Using this product with the protection function disabled
may cause damage to itself. Use special care for this point
when using this mode.
• Canceling DIAG
[1] Before canceling DIAG, execute setting for PRESET of
DIAG menu No.11 (Memory initialization inhibited or
Memory initialized).
* In order to keep the user memory stored, be sure to
select INHIBITED (Memory initialization inhibited).
[2] Turn off the power by pressing the “STANDBY/ON”
key of the main unit.
• Display provided when DIAG started
When the monitor is connected, DIAGNOSTIC MENU
appears on its screen as shown in the figure. (It remains
on display until DIAG is cancelled.)
注意!
プロテクションを解除した状態でのダイアグモードは、
危険な状態でもプロテクションが作動しないため、動作
させると、機器を破壊することがあります。このモード
を使用する場合は十分注意してください。
● プロテクション解除モードでの起動
プロテクションが動作することにより、故障箇所の診断に
支障をきたすような場合は、次の方法によりプロテクショ
ンを解除した状態でダイアグモードに入ることができま
す。(過電流検出以外のプロテクション動作を解除する)
前 ペ ー ジ の 図 に 示 す 2 つ の キ ー を 同 時 に 押 し な が ら
STANDBY/ON キーを押します。このとき、これら2つの
キーを3秒以上押し続けてください。
このモードでは本体FLの SLEEP セグメントが点滅し、
プロテクションを解除した状態でのダイアグモードである
ことを知らせます。
● ダイアグの解除
① ダイアグを解除する前に、ダイアグメニューNo.11の
PRESET (メモリーの初期化禁止/またはメモリーの初
期化)の設定をします。
※ ユーザーメモリーを保持したい場合は、必ずINHIBITED
(メモリー初期化禁止)を選択してください。
② 本体の STANDBY/ON キーを押し、パワーオフにしま
す。
● ダイアグ起動時の表示
モニターを接続してある場合は、モニターの画面に図のよ
うにダイアグメニューの一覧が表示されます。(ダイアグ
を解除するまで、この表示が保持されます)
DIAGNOSTIC MENU
1.YSS938 THR 9.TST NOISE
2.AP32to938 10.RS‑232C
3.938toAP32 11.F.PRESET
4.RAM THR 12.AD CHECK
5.PRO LOGIC 13.SOFT SW
6.DSP BYPASS 14.MC WRITE
7.SPEAKER 15.DSP PCB
8.VFD CHECK 16.SUM/VER
Содержание CinemaDSP digital RX-Z1
Страница 4: ...RX Z1 DSP AZ1 RX Z1 DSP AZ1 RX Z1 A model DSP AZ1 B model 3 DSP AZ1 G model...
Страница 5: ...RX Z1 DSP AZ1 RX Z1 DSP AZ1 4 DSP AZ1 R T K models DSP AZ1 J model DSP AX1UG J model...
Страница 164: ...RX Z1 DSP AZ1 RX Z1 DSP AZ1 184 2 FUNCTION 2 P C B SW351 DSP AX1UG 1 Fig 17 SW351 FUNCTION 2 P C B SW351 Fig 18...