Yamaha CDR-D651 страница 11 Скачать руководство пользователя

Страница: 11 / 36

CDR-D651

Defective IC3.

YES

Is TER waveform
correct?

YES

Is disc dirty,
scratched or
warped?

Check with a known-
good disc.

Error in tracking servo
related section, feed
serve related section or
focus servo related
section, defective pickup.

Error in tracking servo related
section, feed serve related
section or focus servo related
section, defective pickup.

Is disc dirty,
scratched or warped?

YES

Is disc or disc stabilizer in
contact with mechanism?

YES

Check with a known-
good disc.

Poor mechanism accuracy,
deformed floating, rubber or
spring, pickup connector
assembly being caught.

Error in focus serve related
section.

YES

Does focus lock
function work?

Defective IC3, defective
microprocessor.

YES

Defective feed limit switch.

Does tray
loading function
work properly?

YES

Is pickup at the
innermost track?

Faulty tray loading function.

Defective jitter.

YES

Is EFM signal
output?

Error in spindle servo related
section.

YES

Does spindle
motor run?

Defective IC3, defective IC100, 101.

Is muting applied?

YES

Error in muting circuit,
defective microprocessor.

Selected drive and selector
(IC106) are not matched.

YES

Defective IC106 or IC301
IC106 pin10
CD side: L, CDR side: H

Defective microprocessor,
defective loading IC (IC2).

Is FLSW at "L" ?

Defective limit switch, error
in feed servo related section,
defective microprocessor.

YES

Defective motor.

Poor mechanism operation,
wire being caught, loose
gear, etc.

Does tray move
but stop halfway?

YES

Is output obtained at
LOADING terminal?

YES

2) Estimating possible cause from erroneous

operation

a) Tray fails to come out or go in.

When the tray fails to close completely (when the tray
stops halfway)
[Correction]
1) Turn on the power to open the tray.

If it cannot be opened (because the head and tray
contact each other), remove the chucking unit and then
open it.

2) Turn off the power to force the tray to close fully.
3) Turn on the power and open/close the tray so as to

check that the tray closes completely.

b) Sound is not produced or interrupted while playing.

(Time on display advances properly.)

c) “No disc” appears on display.

d) Sound skips. (Time on display does not advance

correctly.)

e) Searching function fails to work.(Sound skips after

searching.)

Содержание CDR-D651





































Результаты поиска

Содержание CDR-D651

Отзывы:

Похожие инструкции для CDR-D651

Бренды по названию

Популярные бренды

Yamaha CDR-D651, Руководство по обслуживанию

Результаты поиска

Содержание CDR-D651

Отзывы:

Похожие инструкции для CDR-D651

Бренды по названию

Популярные бренды