AO8
24
*
FPGA
OK
*
DIR2
OK
2. AO8-IFC3 Test
OK
2. AO8-IFC3 Test
OK
FPGA:
OK
DIR2:
OK
OK
*
SICKB
SICKB:
2.
AO8 - IFC3 Test
This test checks around the AO8-IFC3.
Please refer to the AO8-UNC Test
for charts showing the same detailed
result as those up until now.
NG sample
Please refer to the AO8-UNC Test for NG charts.
C. Inspection Items
The inspection items are as below. Details of the inspection items are shown on the following pages.
* However, 128 Fs Sync must be normal for the DSP to operate, so there is no special check item.
No.
AO8 - UNC test
AO8 - IFC3 test
AO8 - SLOT test
AO8 - IPC4, LED2 test
AO8 - IPC2 test
Item
*
RAM
OK
DataBus
AddressBus
*
Flash
*
Version
OK
OK
1. AO8-UNC Test
OK
1. AO8-UNC Test
OK
RAM:
OK
OK
OK
Flash:
Version:
OK
OK
OK
Now Checking …
Version
NG example
*
ID UNC [1Eh]
ID: unc[1Eh]
*
RAM
NG
DataBus
AddressBus
*
Flash
*
Version
NG
NG
1. AO8-UNC Test
1. AO8-UNC Test
NG
RAM:
NG
Flash:
Version:
NG
NG
NG
*
ID xxx [xxh]
ID: xxx [xxh]
DBus[38-35,32-29,16-13,10-7 pin]
CheckSum = xxxx[xxxx]
Current = x.xx , Latest = x.xx
NG
11111111 11111111
ABus[18-21,24-27,42-44,1-5 pin]
NG
1 11111111 1111111-
DBus[38-35,32-29,16-13,10-7 pin]
00000000 00000000
ABus[18-21,24-27,42-44,1-5 pin]
0 00000000 0000000-
1.
AO8 - UNC Test
This test checks around the AO8-UNC.
OK/NG display for the page as a whole
Displayed when all the checks have been completed.
If OK, sub-items are
not displayed.
Sub-item
Received ID displayed as
board name and hexadecimal
OK/NG display for individual items
The NG is displayed the moment the
item is found to be NG, even if the
test is still underway.
Displays all the detailed results so
far. This display can be scrolled.
Current status display
Using the terminal status display and
the corresponding pin numbers in the
example below, it is possible to
determine that the fifth one from left on
the terminal status display is for pin 32.
Stopped the moment an
actual ID NG appears;
stopped at the end of the
page for any other NG.
Main item
Checked in order from top to bottom.
Completed main items have marks
next to them.
SRAM
OK: LED lit up
NG: LED flashes on (0.2 s) - Off (0.2 s) - On (0.2 s) - Off (0.1 s)
Flash
OK: LED lit up
NG: LED flashes on (0.1 s) - Off (0.1 s) - On (0.1 s) - Off (0.1 s)
(
)
Terminal status display
Delimited in units of 8
digits right justified in the
order upper then lower.
0: Normal 1: Abnormal
-: Ignored
Abnormal port name
Previously read value.
[ ] gives the correct value.
4-digit hexadecimal notation
Gives the current version
and the latest version
Latest Version
Auto Test Start
ALL
CLR
1.
AO8-UNC Test
OK
2.
AO8-IFC3 Test
OK
3.
AO8-SLOT Test
OK
4.
AO8-IPC4, LED2 Test
OK
5.
AO8-IPC2 Test
OK
xxxxxxxx
Input the latest firmware version. When
the version is checked, this character
string and the version actually written in
the firmware are compared. The value
entered here is retained in memory.
Pressing this button starts the automat-
ic checks of the checked items.
The check item and the check results
are displayed. Just one item can be
inspected by pressing its button.
Version character string input example
Only items whose checkboxes are
checked are automatically checked.
ALL checks all the items.
CLEAR removes all the checks.
