Yamaha 8C Скачать руководство пользователя

Страница: 76 / 94

5-3

Trouble

Possible Cause

Remedy

1. Propeller damaged.

2. Propeller pitch or diameter incorrect.

3. Trim angle incorrect.

4. Motor mounted at incorrect height

on transom.

5. Boat bottom fouled with marine

growth.

6. Spark plug(s) fouled or incorrect

type.

7. Weeds or other foreign matter

tangled on gear housing.

8. Fuel system obstructed.

9. Fuel filter clogged.

10. Fuel contaminated or stale.

11. Spark plug gap incorrect.

12. Poor connections or damaged

ignition wiring.

13. Failed ignition parts.

14. Specified engine oil not used.

15. Thermostat faulty or clogged.

16. Air vent screw closed.

17. Fuel pump damaged.

18. Fuel joint connection incorrect.

19. Heat range of spark plug incorrect.

1. Have propeller repaired or

replaced.

2. Install correct propeller to operate

outboard at its recommended

speed (r/min) range.

3. Adjust trim angle to achieve most

efficient operation.

4. Have motor adjusted to proper

transom height.

5. Clean boat bottom.

6. Inspect spark plug(s). Clean or

replace with recommended type.

7. Remove foreign matter and clean

lower unit.

8. Check for pinched or kinked fuel

line or other obstructions in fuel

system.

9. Clean or replace filter.

10. Fill tank with clean, fresh fuel.

11. Inspect and adjust as specified.

12. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

13. Have serviced by a Yamaha

dealer.

14. Check and replace oil with

specified type.

15. Have serviced by a Yamaha

dealer.

16. Open the air vent screw.

17. Have serviced by a Yamaha

dealer.

18. Connect correctly.

19. Inspect spark plug and replace it

with recommended type.

D. Engine power loss.

6M8-F9-17-5 2/4/03 9:49 AM Page 4

Содержание 8C































































































Результаты поиска

Содержание 8C

Отзывы:

Похожие инструкции для 8C

Бренды по названию

Популярные бренды

Yamaha 8C, Руководство пользователя

Результаты поиска

Содержание 8C

Отзывы:

Похожие инструкции для 8C

Бренды по названию

Популярные бренды