Yamaha 8C Скачать руководство пользователя | Manualshive

Страница: 74 / 94

background image

5-1

E

EMU01663¯

TROUBLESHOOTING

A problem in the fuel, compression, or ignition systems can cause poor starting, loss of
power, or other problems. The troubleshooting chart describes basic checks and possi-
ble remedies. (This chart covers all Yamaha outboard motors. Therefore, some items
may not apply to your model.)
If your outboard motor requires repair, bring it to a Yamaha dealer.
If the engine warning indicator is flashing, consult your Yamaha dealer.

A. Starter will not

operate.

Trouble

Possible Cause

Remedy

1. Starter components faulty.

2. Shift lever in gear.

1. Have serviced by a Yamaha

dealer.

2. Shift to neutral.

B. Engine will not

start (Starter

operates).

1. Fuel tank empty.

2. Fuel contaminated or stale.

3. Fuel filter clogged.

4. Starting procedure incorrect.

5. Fuel pump malfunctions.

6. Spark plug(s) fouled or incorrect

type.

7. Spark plug cap(s) fitted incorrectly.

8. Poor connections or damaged

ignition wiring.

9. Ignition parts faulty.

10. Engine stop switch lanyard not

attached.

11. Engine inner parts damaged.

1. Fill tank with clean, fresh fuel.

2. Fill tank with clean, fresh fuel.

3. Clean or replace filter.

4. Read “STARTING ENGINE”

section.

5. Have serviced by a Yamaha

dealer.

6. Inspect spark plug(s). Clean or

replace with recommended type.

7. Check and re-fit cap(s).

8. Check wires for wear or breaks.

Tighten all loose connections.

Replace worn or broken wires.

9. Have serviced by a Yamaha

dealer.

10. Attach lanyard.

11. Have serviced by a Yamaha

dealer.

6M8-F9-17-5 2/4/03 9:49 AM Page 2

«
...
72
73
74
75
76
...
»

Содержание 8C































































































Отзывы:

Нет отзывов

Похожие инструкции для 8C

2.7-litre V6 Biturbo

Бренд: Audi Страницы: 72

Бренд: Deutz Страницы: 257

Бренд: Arrow Shark Страницы: 16

Бренд: Metronic Страницы: 28

Бренд: Lombardini Страницы: 50

Бренд: Lombardini Страницы: 114

Бренд: Texas Equipment Страницы: 25

Бренд: Detroit Diesel Страницы: 22

Бренд: panthera Страницы: 12

Бренд: Yamakoyo Страницы: 41

Бренд: Waukesha Страницы: 140

Бренд: CAB Страницы: 16

Бренд: Marinediesel Страницы: 248

Бренд: Vetus Страницы: 72

Бренд: Yanmar Страницы: 394

Volt Electric Drive

Бренд: Native Watercraft Страницы: 8

Бренд: Baja motorsports Страницы: 33

Бренд: Man Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды