Yamaha 2008 YZF-R1X Скачать руководство пользователя | Manualshive

Страница: 20 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-4

3

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “

”

and “

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11250

Oil level warning light “

”

This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.

NOTE:

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If the oil lev-
el detection circuit is defective, the
following cycle will be repeated un-
til the malfunction is corrected: The
oil level warning light will flash ten
times, then go off for 2.5 seconds.
If this occurs, have a Yamaha
dealer check the vehicle.

EAU11361

Fuel level warning light “

”

This warning light comes on when the
fuel level drops below approximately
3.2 L (0.85 US gal) (0.70 Imp.gal).
When this occurs, refuel as soon as
possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, and then go off,
have a Yamaha dealer check the elec-
trical circuit.

1. Left turn signal indicator light “

”

2. Neutral indicator light “

”

3. High beam indicator light “

”

4. Right turn signal indicator light “

”

5. Fuel level warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

8. Shift timing indicator light

9. Engine trouble warning light “

”

10.Immobilizer system indicator light

U4C821E0.book Page 4 Tuesday, July 17, 2007 11:37 AM

«
...
18
19
20
21
22
...
»

Содержание 2008 YZF-R1X













































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 YZF-R1X

Бренд: Can-Am Страницы: 16

Бренд: Can-Am Страницы: 254

Бренд: National Cycle Страницы: 3

Бренд: VIKING BAGS Страницы: 2

Бренд: Yoshimura Страницы: 4

Бренд: National Cycle Страницы: 2

Бренд: Shark Страницы: 18

Бренд: hepco & becker Страницы: 4

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 8

MSS X9 EVOLUTION 250

Бренд: PIAGGIO Страницы: 262

MP3 500 ie SPORT Business LT 2011

Бренд: PIAGGIO Страницы: 375

Бренд: Ossa Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды