Yamaha 2006 V Star XVS650AV Скачать руководство пользователя страница 75

Страница: 75 / 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

3. Lift the front wheel off the ground

according to the procedure on
page 6-32.

4. Pull the wheel axle out, and then

remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU24932

To install the front wheel

1. Install the speedometer gear unit

into the wheel hub so that the pro-
jections mesh with the slots.

2. Lift the wheel up between the fork

legs.

NOTE:

Make sure that there is enough space
between the brake pads before insert-
ing the brake disc and that the slot in
the speedometer gear unit fits over the
retainer on the fork leg.

3. Insert the wheel axle.
4. Lower the front wheel so that it is

on the ground.

5. Tighten the wheel axle to the spec-

ified torque.

6. Tighten the front wheel axle pinch

bolt to the specified torque.

7. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

8. Connect the speedometer cable.

1. Wheel axle
2. Front wheel axle pinch bolt

1. Speedometer gear unit

2. Speedometer cable
3. Retainer

Tightening torque:

Wheel axle:

59 Nm (5.9 m·kgf, 43 ft·lbf)

Tightening torque:

Front wheel axle pinch bolt:

20 Nm (2.0 m·kgf, 14 ft·lbf)

U3B720E0.book Page 33 Friday, April 15, 2005 1:34 PM

Содержание 2006 V Star XVS650AV





























































































Результаты поиска

Содержание 2006 V Star XVS650AV

Отзывы:

Похожие инструкции для 2006 V Star XVS650AV

Бренды по названию

Популярные бренды

Yamaha 2006 V Star XVS650AV, Руководство пользователя

Результаты поиска

Содержание 2006 V Star XVS650AV

Отзывы:

Похожие инструкции для 2006 V Star XVS650AV

Бренды по названию

Популярные бренды