Yamaha 2006 FZ6-S Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 94

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-20

6

EAU36501

Rear brake light switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, have a Yamaha dealer ad-
just the brake light switch.

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22420

Front brake pads

Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear

indicator groove has almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 1.0 mm (0.04 in),
have a Yamaha dealer replace the
brake pads as a set.

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

1. Lining thickness

U1B3E3E0.book Page 20 Friday, July 14, 2006 11:34 AM

«
...
58
59
60
61
62
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: DAELIM Страницы: 2

Бренд: GAS GAS Страницы: 56

Бренд: CB Sabbiatrici Страницы: 43

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

KTM 1190 LED Light Bar

Бренд: CYCLOPS Страницы: 4

Bonneville T100

Бренд: Triumph Страницы: 198

Бренд: Triumph Страницы: 53

Бренд: kellermann Страницы: 2

Бренд: Honda Страницы: 26

Бренд: rizoma Страницы: 16

Light Bee QL3000DY

Бренд: Surron Страницы: 18

Бренд: KTM Страницы: 36

690 SMC R 2016 Series

Бренд: KTM Страницы: 18

Бренд: yasuni Страницы: 8

Бренд: DYNATEK Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды