Yamaha 2006 FZ6-S Скачать руководство пользователя | Manualshive

Страница: 47 / 94

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-7

6

Before installing a spark plug, the spark
plug gap should be measured with a
wire thickness gauge and, if necessary,
adjusted to specification.

Clean the surface of the spark plug
gasket and its mating surface, and then
wipe off any grime from the spark plug
threads.

NOTE:

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.

EAU32852

Engine oil and oil filter car-
tridge

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

NOTE:

Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles.

1. Spark plug gap

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Tightening torque:

Spark plug:

17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)

U1B3E3E0.book Page 7 Friday, July 14, 2006 11:34 AM

«
...
45
46
47
48
49
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: N-Com Страницы: 2

Бренд: N-Com Страницы: 64

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренд: Honda Страницы: 100

Бренд: GAS GAS Страницы: 32

Easyrack 6617501 01 01

Бренд: hepco & becker Страницы: 4

2001 GSX1300RK1 HAYABUSA

Бренд: Suzuki Страницы: 31

Бренд: Dakota Digital Страницы: 11

SCARABEO 100 4T - 06-2001 PART6

Бренд: APRILIA Страницы: 6

Бренд: hepco & becker Страницы: 2

Бренд: Star Motorcycles Страницы: 19

Бренд: Malaguti Страницы: 50

Бренд: Malaguti Страницы: 112

Бренд: Baotian Страницы: 22

Бренд: Rockford Fosgate Страницы: 8

Бренд: APRILIA Страницы: 235

390 Duke AR 2018

Бренд: KTM Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды