manualshive.com logo in svg

YAMADA G25, Руководство по обслуживанию, Страница: 3 / 12

Поделиться
Скачать
YAMADA G25 Скачать руководство пользователя страница 3

 

 
 
 

Table of Contents 

 

·Warnings and Cautions

 

·Table of Contents

 

  1.Principles of operation

 ------------------------------------------------------------ 1 

 2.

 

Maintenance and Tools 

 

 2.1 Maintenance ----------------------------------------------------------------------- 1 

 

 2.2 General tools ----------------------------------------------------------------------- 1 

 

 2.3 Special tools ------------------------------------------------------------------------ 1 

 

 2.4 Misc. --------------------------------------------------------------------------------- 1 

  3.Ordering Replacement parts

 --------------------------------------------------- 1 

  4.Balls, Valve seats 

 

 4.1 Removal ----------------------------------------------------------------------------- 2 

 

 4.2 Inspection -------------------------------------------------------------------------- 3 

 

 4.3 Installation ------------------------------------------------------------------------- 3 

  5.Diaphragm and Center rod 

 

 5.1 Removal ----------------------------------------------------------------------------- 4 

 

 5.2 Inspection -------------------------------------------------------------------------- 4 

 

 5.3 Installation ------------------------------------------------------------------------- 5 

 6.Guide bush 

 

 6.1 Removal ----------------------------------------------------------------------------- 6 

 

 6.2 Inspection -------------------------------------------------------------------------- 6 

 

 6.3 Installation ------------------------------------------------------------------------- 6 

  7.Spool valve assembly and Sleeve 

 

 7.1 Removal ----------------------------------------------------------------------------- 7 

 

 7.2 Inspection -------------------------------------------------------------------------- 8 

 

 7.3 Installation ------------------------------------------------------------------------- 8 

8.Retightening of Tie rods

 ---------------------------------------------------------- 8 

 

 

 

 
 

 

Содержание G25













Отзывы:

Нет отзывов