YAMADA 125 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

YAMADA 125 Series Скачать руководство пользователя страница 15

10

④

Check for loose bolts and nuts

Check bolts and nuts according to the following procedures:
- Completely shut down the pump and lift by disconnecting from

the air source, for example.

- Ensure that all visible bolts and nuts on the pump and lift cannot

be loosened by hand.

⑤

Clean and lubricate lift rail

Clean and lubricate according to the following procedures:
-  Shut off the lift.
-  Wipe off any visible contaminated grease on the lift rail.
-  Apply clean grease (lithium soap based grease: No.1) to slide

rail grooves. (Fig. 10)

- Move the lift to clean and lubricate the other section of the rail.

⑥

Overhaul pump

Pump needs to be overhauled triennially. Please contact the retail
store where you purchased your pump or our business office for
overhaul. Earlier overhaul is recommended depending on use
frequency and deterioration degree.

Lift rail

Bolt

Slide rail groove

Fig. 10

Where to apply grease on lift rail

«
...
13
14
15
16
17
...
»

Содержание 125 Series

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды