Yaesu G-1000SA Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

Yaesu G-1000SA Скачать руководство пользователя страница 2

I

MPORTANT

!

The installation of a rotatable antenna on a tower system is a dangerous and potentially life-threatening task, if due care
is not taken.

A tower must never be installed in a position where it could fall across power distribution cables in the event of a
catastrophic tower failure during a windstorm or earthquake.

The control cable attached to this rotator could, in the event of a nearby or direct lightning strike, carry lethal voltages
down the cable and into your home. Yaesu strongly recommends the installation of suitable lightning arrestors on all
control cables and coaxial lead-in cables from your antenna installation. See your dealer for details of available light-
ning-protection devices.

If an electrical storm should be reported in your area, quickly unplug the control cable from the rear of the rotator’s
controller box, and disconnect the AC cable from the wall outlet. Disconnect the coaxial cable(s) from the antenna(s) as
well.

Do this only if the lightning is not in your immediate area, as you could be killed instantly if lightning should

strike while you are holding a cable.

If you have any doubts about your ability to install this rotator safely, enlist the services of a professional antenna
installation company.

«
1
2
3
4
...
»

Содержание G-1000SA

















Отзывы:

Нет отзывов