Yaesu FT-818ND Скачать руководство пользователя страница 62

Страница: 62 / 76

Menu Operation

Menu Item 37 [MIC SCAN]

Function

: Enable/disable scanning access via the microphone’s [

]/[

DWN

] keys.

Available Values

: OFF/ON

Default

: ON

Menu Item 38 [OP FILTER]

Function

: Enable the optional filter (CW or SSB) path.

Available Values

: OFF/SSB/CW

Default

: OFF

After installing the optional filter, set this Menu Item to define the signal path corresponding
top the filter you have installed.

Menu Item 39 [PKT MIC]

Function

: Adjust the audio input level from the TNC during 1200 bps Packet operation.

Available Values

: 0 ~ 100

Default

: 50

Menu Item 40 [PKT RATE]

Function

: Set the transceiver’s circuitry for the Packet baud rate to be used.

Available Values

: 1200/9600 bps

Default

: 1200 bps

Menu Item 41 [RESUME]

Function

: Set the delay time for scanning resumption.

Available Values

: OFF/3/5/10 seconds

Default

: 5 sec

When this Menu Item set to “OFF,” the scanner stops (without restarting) until you press
the

(SCN) key (or the microphone’s [

]/[

DWN

] keys).

Menu Item 42 [RPT SHIFT]

Function

: Set the magnitude of the Repeater Shift.

Available Values

: 0 ~ 99.99 MHz

Default

: Depends on transceiver version, and the band in use.

Each band’s repeater shift (HF/50/144/430 MHz) may be set independently.

Menu Item 43 [SCOPE]

Function

: Select the Spectrum Scope mode.

Available Values

: CONT/CHK

Default

: CONT

CONT: The Spectrum Scope sweeps continuously.
CHK: The Spectrum Scope sweeps one cycle every 10 seconds.

Menu Item 44 [SIDETONE]

Function

: Adjust the CW sidetone volume level.

Available Values

: 0 ~ 100

Default

: 50

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды