Page 117
FT-2000 O
PERATING
M
ANUAL
054 A1A F-TYPE
Function
: Selects the desired keyer operation mode for
the device connected to the front panel’s
KEY
jack.
Available Values
: OFF / buG / ELE / ACS
Default Setting
: ELE
OFF: Disables the front panel’s keyer (“straight key”
mode for use with external keyer or computer-
driven keying interface).
buG: Mechanical “bug” keyer emulation. One paddle
produces “dits” automatically, while the other
paddle manually produces “dahs.”
ELE: Iambic keyer with ACS (Automatic Character
Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Character
Spacing) enabled.
055 A1A F-REV
Function
: Selects the keyer paddle’s wiring configuration
for the
KEY
jack on the front panel.
Available Values
: nor / rEU (REV)
Default Setting
: nor
nor:
Tip = Dot, Ring = Dash, Shaft = Ground
rEU (REV): Tip = Dash, Ring = Dot, Shaft = Ground
056 A1A R-TYPE
Function
: Selects the desired keyer operation mode for
the device connected to the rear panel’s
KEY
jack.
Available Values
: OFF / buG / ELE / ACS
Default Setting
: ELE
OFF: Disables the rear panel’s keyer (“straight key”
mode for use with external keyer or computer-
driven keying interface).
buG: Mechanical “bug” keyer emulation. One paddle
produces “dits” automatically, while the other
paddle manually produces “dahs.”
ELE: Iambic keyer with ACS (Automatic Character
Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Character
Spacing) enabled.
057 A1A R-REV
Function
: Selects the keyer paddle’s wiring configuration
for the
KEY
jack on the rear panel.
Available Values
: nor / rEU (REV)
Default Setting
: nor
nor:
Tip = Dot, Ring = Dash, Shaft = Ground
rEU (REV): Tip = Dash, Ring = Dot, Shaft = Ground
058 A1A CW AUTO
Function
: Enables/disables CW keying while operating
on SSB.
Available Values
: OFF / 50 / On
Default Setting
: OFF
OFF: Disables CW keying while operating on SSB.
50:
Enables CW keying only while operating SSB
on 50 MHz (but not HF).
On: Enables CW keying while operating on SSB (all
TX bands).
N
OTE
:
This feature allows you to move someone from SSB to
CW without having to change modes on the front panel.
059 A1A BFO
Function
: Sets the CW carrier oscillator injection side for
the CW mode.
Available Values
: USb / LSb / Auto
Default Setting
: USb
USb: Injects the CW carrier oscillator on the USB side.
LSb: Injects the CW carrier oscillator on the LSB side.
Auto: Injects the CW carrier oscillator on the LSB side
while operating on the 7 MHz band and below,
and the USB side while operating on the 10 MHz
band and up.
060 A1A BK-IN
Function
: Sets the CW “break-in” mode.
Available Values
: SEni / FuLL
Default Setting
: SEni
SEni (SEMI): The transceiver will operate in the semi
break-in mode. The delay (receiver re-
covery) time is set by the front panel’s
[
DELAY
] knob.
FuLL:
The transceiver will operate in the full
break-in (QSK) mode.
061 A1A SHAPE
Function
: Selects the CW carrier wave-form shape (rise/
fall times).
Available Values
: 1 / 2 / 4 / 6 msec
Default Setting
: 4 msec
062 A1A WEIGHT
Function
: Sets the Dot:Dash ratio for the built-in elec-
tronic keyer.
Available Values
: (1:) 2.5 ~ 4.5
Default Setting
: 3.0
M
ENU
M
ODE
MODE-CW G
ROUP
