13
14
1
Remove makeup and gently cleanse your face.
• Remove oil and dirt from your skin so that it is in a clean condition prior to treatment.
* COOL Mode can be used over makeup.
3
Connect the AC adapter, press and hold the POWER button. Press the
mode button and select a mode and intensity level.
• First, briefly press the button of the mode you wish to use to start. Then press the same button again
briefly to select the level.
• Start using the device in EYE Mode only after rotating the electrode head.
* There is no treatment level selection available for COOL Mode.
* Use only Level 1 upon the first use and until you are accustomed to use.
2
Attach a cotton pad if necessary and apply skin lotion onto it.
Treatment Method
5
Press and hold the POWER button to turn the power off. Disconnect the
AC adapter from the main unit and the wall outlet.
After treatment, condition your skin as necessary.
• Please apply skin cream as appropriate.
* Clean the main unit after each use (page 17).
6
4
Gently apply the treatment head to your skin and move the head over the
area being treated. Refer to pages 15 and 16 for more details.
• When operation in each mode is completed, the device will switch to Standby Mode. To start the next
mode, press the relevant mode button briefly.
* During use, make sure the electrode head is closely touching the skin.
* If you wish to stop the mode you are using half-way through the operation, press and hold the POWER
button.
Remove all metal accessories (watches, necklaces, rings, earrings, etc.) when using the device. Failure
to comply may cause accidents or injuries.
Please reapply skin-care products or water during treatment to ensure that there is always some liquid
between the electrode head and the skin. If there is an insufficient amount of skin-care products or
water, the stimulation will weaken, causing skin problems.
Please carefully clean the parts of the device that come into contact with the skin every time you use it
and keep the device clean at all times. Failure to comply may cause skin problems.
If you feel an unpleasant tingling on your skin, reduce the intensity level or move to another area.
You could also moisten the skin with water, lotion, or gel before using the device.
Failure to comply may cause skin damage.
Ho
w to Use
Ho
w to Use
How to attach cotton pad to the electrode head
1
Remove the cotton stopper from the
electrode head.
2
Place a piece of cotton pad on top of the electrode head
and press the cotton stopper down over the cotton pad.
* If the cotton stopper does not fit properly on the electrode head, please use a larger and thinner
piece of cotton pad. Because thick cotton pads are difficult to fix in place, split them in half before
use.
* If the cotton pad is too thick, the thermal action of RF treatment may be adversely affected and
you will feel less heat.
3
Apply your regular skin lotion or gel onto the cotton pad.
* Make sure the skin lotion or gel coats the entire surface of the electrode head.
* If using a waterly (low-viscosity) skin lotion, the feeling of warmth may decrease.
Recommended skin lotions: RF Booster Pad or high-viscosity skin lotions.
* If the cotton pad becomes dry, add more skin-care product. Cotton pads may easily come off
from the device when they are dry.
How to Use
How to Use (General Instructions)
Precautions
Be sure to move the device on your skin while using. Using the device continuously on the same area
may cause burns or other injuries (except in COOL Mode).
The warmth of the RF changes depending on the type of skin-care product used and the skin’s
condition at the time of treatment.
Do not use this device around the eyes unless it is in EYE Mode or COOL Mode.
* The LED light can be used around the eyes and eyelids. Close your eyes and hold the device at least
5 cm away from the skin.
Do not look directly into the LED light.
The recommended ambient temperature is 15° C to 30°C.
Make sure to remove makeup before using the device on your face. If you use the device over makeup,
the foundation may cause dark staining of the skin.
