Xyron XM2500 Скачать руководство пользователя страница 4

Step 3:

On the bottom 
supply roll, grasp 
the laminated starter
section by the leading
edge film.

Route over the bot-
tom idler bar adjacent
to

the lower

rubber roller.

Make sure the film 
is inserted squarely.
Rotate the handle 1/4 
turn in the direction of
the arrows.

Step 4:

Make certain the
lower film is tight. 
If necessary, rotate 
the supply roll in the 
direction of the arrows
until the film is taut.

Grasp the film from 
the upper supply roll
and adhere it to the
film on the lower 
supply roll.

By carefully aligning the
edges, keeping the 
film tight and avoiding 
wrinkles, film waste will be
minimized.

Step 5:

Rotate the handle to
pull the supplies
through the machine.

Ensure that the film
exits between the
blade bars.

Just before the top
film 
becomes tight again,
insert a small piece of
cardstock between
the rubber rollers.
This will help to mini-
mize waste and
ensure the film exits
between the upper
cut bar and lower
guide.

Step 6:

Continue to crank film through
machine until it is aligned and 
wrinkle-free.

Trim off excess film by pressing down
on the blade holder and sliding in
either direction.

Step 7:

Replace the top cover.

Close the lower access door.

Install feed tray completely by align-
ing the support posts in the grooves 
located in the sides of the machine.

When done correctly, the film layers should be aligned and wrinkle-free after 18"
(45cm) of material has exited the machine.

Содержание XM2500











Отзывы: