Xylem MJK pHix Compact V3 Скачать руководство пользователя страница 14

Страница: 14 / 88

pHix® Compact V3. NG (next generation)

EN 4.10 Version 2103

Mounting /Mechanical mounting

2.
3.
4.

THE US

ALL OTHERS

pHix® Compact conforms to pressure class PN 5, and can therefore be
mounted in closed systems with a working pressure of

max. 72 psi / 5 bar.

Mounting in open channels and reservoirs

Due to the lifetime of the electrode and measurement accuracy, the following
should be complied with when mounting pHix® Compact.

pHix® Compact should be mounted on a location with a good liquid
circulation.
The electrode tip should be minimum 30 cm below the liquid surface.
The electrode tip must

not

touch the bottom.

The cable must

not

be suspended in a cable bracket.

Содержание MJK pHix Compact V3

























































































Результаты поиска

Содержание MJK pHix Compact V3

Отзывы:

Похожие инструкции для MJK pHix Compact V3

Бренды по названию

Популярные бренды

Xylem MJK pHix Compact V3, Руководство пользователя

Результаты поиска

Содержание MJK pHix Compact V3

Отзывы:

Похожие инструкции для MJK pHix Compact V3

Бренды по названию

Популярные бренды