Xylem AC Fire Pump 8100 Series Скачать руководство пользователя страница 37

AC6102 Rev 0

5

 

36 

8.

Allow the bearing to cool to room temperature. Coat the

exposed sides with 2 to 3 oz. [55 to 85 g] of the
recommended grease.

9.

Coat the inside of the bearing housing [3-025-4] with

grease and slide into place over the bearing. Attach the
bearing housing to the stuffing box with four cap screws
[3-909-9].

10. Repeat steps for the inboard end.

10.4.3.2  Series 8150

 

1.

Install slingers [3-136-9] onto shaft.

2.

Press a new lip seal [3-177-2] into bearing brackets
[3-025-5].

NOTE:

 Seal lip or pressure side of seal must point

away from the bearing.

3.

Place bearing brackets onto shaft. Install backing snap
rings [0-915-0] into the shaft grooves.

4.

Heat the bearings [3-026-2], using either a dry heat, or
a 10-15% soluble oil and water solution.

NOTE:

 Do not exceed 275°F [135°C].

5.

Using gloves slide the heated bearings onto the shaft.
The shielded side of the bearing goes on first.

6.

Install the beveled snap ring [3-177-3] into the groove
on the shaft, outboard side only.

7.

Slide the bearing housings [3-025-3, 3-025-4] into place
over the bearings.

10.4.3.3  Series 8200 

1.

Press a new lip seal [3-177-9] into each bearing cap [5-

018-0].

NOTE:

 Seal lip or pressure  side of seal must point away 

from the end of the shaft the lip seal is assembled on. 

2.

Place two O-rings [6-914-9] on each stuffing box

bushing [6-008-0], and then slide over the shaft sleeve
with the beveled end facing the impeller.

3.

Slide the deflectors [3-136-9] and bearing caps onto the

shaft. Install snap ring [5-915-3] on the inboard side of
the shaft. Install the split ring [5-050-4] and retaining
collar [5-421-4] on the outboard side of the shaft.

4.

Heat the bearings [3-026-3-026-4], using either a dry

heat, or a 10-15% soluble oil and water solution.

NOTE:

 Do not exceed 275°F [135°C].

5.

Using gloves slide the heated bearing [3-026-3] onto the

inboard end of the shaft against the snap ring.

6.

Using gloves slide the two heated bearing [3-026-4]

onto the outboard end of the shaft. These bearings
must be installed back to back. Place the first bearing
on the shaft; when installing the second bearing, push
against the inner race to remove all clearance between
the inner races of the two bearings, and between the
inner race of the first bearing and the retaining collar.

7.

Install the lock washer [3-517-4] and locknut [3-516-4]

on the outboard end of the shaft. Ensure that the
locknut is secured and then bend over the tabs on the
lock washer.

8.

Allow the bearings to cool to room temperature. Coat

the exposed sides with 2 to 3 oz. [55 to 85 g] of the
recommended grease.

9.

Slide the bearing housings [3-025-3, 3-025-4] into place

over the bearing. Attach the bearing caps to the bearing
housing with four cap screws [5-904-9].

10.4.3.4  Series 9100

 

1.

Press bearing isolators [1-333-1] in each bearing cover

[3-018-3, 3-018-4]. Install gaskets [3-409-9] on each
bearing cover.

NOTE:

 Inboard bearing cover [3-018-3] is 1/4 in.

[6.4mm] less in width than outboard [3-018-4].

2.

Slide bearing covers onto the shaft. Install the snap

rings [3-915-9]. Install thrust washer on the outboard
end.

3.

Heat the bearings [3-026-2], using either a dry heat, or

a 10-15% soluble oil and water solution.

NOTE:

 Do not exceed 275°F [135°C].

4.

Using gloves slide the heated bearing [3-026-2] onto the

shaft against the snap ring on the inboard end and the
thrust washer on the outboard end.

5.

Install the lock washer [3-517-4] and locknut [3-516-4]

on the outboard end of the shaft. Ensure that the
locknut is secured and then bend over the tabs on the
lock washer.

6.

Allow the bearings to cool to room temperature. Coat

the exposed sides with 2 to 3 oz. [55 to 85g] of the
recommended grease.

7.

Press a bearing isolator [1-333-1] in the inboard bearing

housing and an oil seal [3-177-4] in the outboard
bearing housing.

8.

Slide the bearing housings [3-025-2] into place over the

bearings. Attach the bearing covers to the bearing
housing with two cap screws [3-904-9].

10.4.4  Rotating element 

After completion of the preceding steps, carefully place the 
shaft assembly into the lower half pump casing.

 

10.4.4.1  Series 8100

 

1.

Set the rotating element in the pump casing [2-001-0],

assuring correct rotation. Locate both stuffing box
tongues in their respective casing grooves.

2.

Locate pins [3-943-9] in the stuffing box and the casing

wear rings in their respective slots at the casing parting
line. Correct any O-ring bulging.

10.4.4.2  Series 8150 

1.

Set the rotating element in the pump casing [2-001-0],
assuring correct rotation. Correctly locate casing ring
pins in the casing main slot. (Sliding the inboard bearing
housing towards the coupling slightly will ease
assembly).

2.

Bolt the outboard bearing housing in place. Ensure that
both housings are seated properly in the lower half
casing.

3.

Bolt inboard bearing housing in place. Rotating element
should now turn freely.

4.

Adjust the shaft sleeve nuts to get the impeller centered
in the casing water passage.

5.

Tighten the sleeve nut set screws.

10.4.4.3  Series 8200

 

1.

Set the rotating element in the pump casing [2-001-8],

assuring correct rotation. Correctly locate casing ring
pins, stuffing box bushing pins, and interstage
diaphragm pins in the casing main joint slots. (Sliding

Содержание AC Fire Pump 8100 Series























































Отзывы: