background image

WOOD CHIPPER

11

GB

Feed Hopper

The Feed Hopper is on top the unit. Always 
load leaves and other light waste into the 
hopper opening. Never insert hands into the 
hopper opening.

Chipper Cone

The Chipper Cone is located on the front 
of the unit, and next to the engine. Insert 
branches and tree limbs no larger than 7.6cm 
(3") in diameter into the chipper cone opening. 
Never insert hands past the cone opening.

Collection Bag

The Collection Bag captures all debris 
discharged from the unit. Do not operate the 
unit without the collection bag in place.

Deflector

Chipped debris are discharged through the 
Deflector opening. The deflector can be 
attached to the chute.

Grip Handles

The handles are used to move the unit.

Transport Wheels

To move the chipper, grip the handles located 
on the top of the opening of the hopper and 
tilt the machine back until it is fully resting on 
the tires.

Engine On/Off Switch

The engine switch has two positions. OFF - 
engine will not start or run. ON - engine will 
start and run.

Recoil Starter Handle

 

The handle is used to start the engine.

Fuel Shut-Off Valve

 

The fuel shut off lever has two positions: Open 
(

) and Closed (

). Use the Open position 

when operating, and use the closed position 
for servicing, transporting, or storing the unit. 
OPEN (

) - use this position to run the unit.

Choke Control

 

The choke control is used to choke the 
carburetor and assist in starting the engine. 
The choke control slides between the CHOKE 
CLOSED 

 and CHOKE OPEN 

 positions.

Add Oil To Engine

1.    Make sure the chipper 

is on a flat, level surface.

2.   Remove the oil fill cap/

dipstick to add oil.

3.   Using a funnel, add oil up to the 

FULL

 mark 

on the dipstick. (See engine manual for oil 
capacity, oil recommendation, and location 
of fill cap.)

Add Gasoline to Engine

CLOSED

OPEN

Throttle Control

The throttle control regulates the speed of 
the engine and will shut off the engine when 
it is moved to the STOP position. The throttle 
control moves between FAST 

, SLOW 

and STOP positions.

Wood Chipper Operation

The engine is shipped without oil. 
Do not start the engine before 
adding oil.

Gasoline is highly flammable and 
explosive. You can be burned or 
seriously injured when handling fuel. 
Use extreme care when handling 
gasoline.

Fill the fuel tank outdoors, never 
indoors. Gasoline vapors can ignite 
if they collect inside an enclosure. 
Explosion can result.

DO NOT OVERFILL. Check engine 
oil level daily and add as needed.

36060UK00M100_BS.indd   11

2019/8/28   14:44:24

Содержание 61038






















Отзывы: