background image

11

OPERATION

FOR OUTDOOR USE ONLY. NEVER USE INSIDE 

A HOUSE OR OTHER UNVENTILATED OR 

ENCLOSED AREAS. THIS HEATER CONSUMES 

AIR (OXYGEN). 

EXPLOSION - FIRE HAZARD

• 

NEVER

 store propane near high heat, open flames, pilot lights, direct sunlight or other ignition sources or 

where temperatures exceed 120°F (49°C).

•  Propane vapors are heavier than air and can accumulate on low places. If you small gas, leave the area 

immediately. 

• 

NEVER

 install or remove cylinder while the heater is lit, near flame, pilot lights, other ignition sources or 

while the heater is hot to the touch.

• This heater is red hot during use and can ignite flammables that are too close to the burner. Keep flammables 

at least 2 feet from the sides and 3 feet from the top. Keep gasoline and other flammable liquids and vapors 

well away from the heater. 

• The propane cylinder must always be stored outdoors in a well ventilated space. 

NEVER

 store the propane 

cylinder in an enclosed area. If the heater is to be stored indoors, disconnect the propane cylinder for outdoor 

storage. 

To Turn the Heater On:

1.

 Turn on the valve on the gas supply to the cylinder. 

2. 

Press and turn the variable control knob to the 

HIGH

 position. 

3.

 Press down the variable control knob, press the 

IGNITOR

 button several times until the burner head flame 

ignites. Release the variable control knob 10 seconds after the ignition. 

• If a new tank has just been connected, allow at least one minute or more for the air in the gas pipeline to 

purge out through the pilot hole, or simply do step 3. 

• When lighting the flame, make sure the variable control knob is continuously depressed while pressing the 

IGNITOR

 button. The variable control knob can be released after the flame is lit for 10 seconds. 

• The flame can be detected and watched through the peep-hole located on the base of the burner.

• If only a small flame is needed, turn the variable control knob to the 

LOW

 position. 

4. Turn the variable control knob to 

LOW

 position for 5 minutes or more before turning the knob to the desired 

temperature setting. 

5. If the burner flame accidentally goes out, turn the heater 

OFF

 and wait at least 5 minutes to let the gas 

dissipate before lighting again to avoid a possible explosion. Repeat steps 2 through 4. 

Содержание 96050
















Отзывы: