manualshive.com logo in svg

Xtreme Garage 425-1636, Руководство пользователя, Страница: 24 / 28

Поделиться
Скачать
Xtreme Garage 425-1636 Скачать руководство пользователя страница 24

 

 

24

 

 

Door Status vs. Activation

 

! 

WARNING

 

To Prevent SERIOUS INJURY or DEATH:

 

-

 Use Emergency Release to disconnect Trolley ONLY when the door is CLOSED to prevent unexpected rapid falling in 

case of a unbalanced / poor

-

conditioned door.

 

-

 Use Emergency Release ONLY when doorway is clear of persons and obstructions.

 

-

 DO NOT use Emergency Release to pull the door open or closed.

 

In  case  of  a  power  failure  or  door  obstruction,  PULL 
EMERGENCY Knob to release door from Opener.

 

To Disconnect Trolley for Manual Operation

 

With  the  door  closed,  pull  down  the  emergency  release  knob  to 
the  DISCONNECT  position.  The  door  can  be  raised  /  lowered 
manually.

 

To Re

-

connect Trolley

 

Pull the knob toward the Opener so that the lever will flip up to the 
CONNECT  position.  The  Trolley  will  reconnect  itself  when  the 
Opener is activated or when the door is manually opened/closed.

 

Lever

 

CONNECT

 

DISCONNECT

 

Pull to Disconnect

 

Flip to reconnect

 

Manual Operation

 

Door status

 

                   Activation using Wall Panel / Transmitter

 

Door at fully open / close position

 

Door will move to fully close / open position

 

Door is closing

 

Door will reverse

 

Door is opening

 

Door will stop

 

Door is stopped as intended in partially open position

 

Close

 

Door is obstructed while closing

 

Door will reverse and Beep x 20

 

Door is obstructed while opening

 

Door will stop and Beep x 25

 

Door is fully opened and Photo Eye System is obstructed

 

Door will not close

 

Operating the Opener

 

Operation / Condition

 

        

 

Opener is initially plugged

-

in (no travel limits stored see 

pages 16,17,18)

 

Flash x 5

 

Reconnecting power (with travel limits stored)

 

Flash x 3

 

“LEARN” button is pressed

 

Beep x 1

 

Upon activation

 

Light On for 2.5 minutes

 

Upon activation by remote transmitters

 

Beep x 1, Light On for 2.5 minutes

 

Remote Transmitter / Keyless Entry PIN code accepted

 

Beep x 2

 

Photo Eye System is obstructed during door

-

closing

 

Beep x 20

 

The door is obstructed during travel

 

Beep x 25

 

Door travels with abnormal speed

 

Beep x 12 (1 beep / second)

 

Courtesy Light / Buzzer Responses

 

Courtesy Light / Buzzer Responses

 

NOTICE: This opener will not work until you set the travel limits and the auto force adjustment. You must follow 
all steps located on pages 16,17,18.

 

Soft Open / Soft Close Feature:  The opener is designed to start slowly, accelerate to full speed,  then slowly 
stop.  The soft open/close is designed to reduce strain on the openers components and to improve opener 
longevity.  

 

Содержание 425-1636





























Отзывы:

Нет отзывов