Xtrails VESDA-E VEP-A00 Скачать руководство пользователя страница 67

Страница: 67 / 109

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

5.5.5

Airflow Options

The Airflow options provide the ability to set:

limits for what the detector considers to be normal airflow behavior for the sampling pipe network

which pipe inlets are being used

aspirator speed

These settings should be confirmed in the ASPIRE design of the sampling pipe network.

Note:

Refer to Section 5.6 for the default settings.

Figure 5-15: Airflow Options

The Airflow configuration options are as follows:

Air Flow:

The air flow conditions, as a percentage of the normalized air flow, that will cause a fault to be

reported. If the installation site flow conditions vary significantly, it is recommended that the Major High
and Major Low parameters are set closer to their limits.

Major High:

The level of air flow considered to be so far above normal as to require urgent attention.

Minor High:

The level of air flow considered to be above normal but not urgent.

Minor Low:

The level of air flow considered to be below normal but not urgent.

Major Low:

The level of air flow considered to be so far below normal as to require urgent attention.

Note:

The number of pipes able to be configured matches the number of pipes supported by the
detector.

Significant Flow Change:

The amount of airflow change at which an event is recorded in the event log.

Delay:

The length of time between the air flow fault threshold being reached and the fault relay operation.

Pipes in Use:

The pipes that are actually being used. Refer to Section 3.3 on page 15 for further

information. This setting is not available for the VEP-A00-1P.

Aspirator:

Select the required Aspirator Speed setting 1 through 5, as determined using ASPIRE. This

setting is not available for the VEP-A00-1P.

5.5.6

Filter Option

The Filter option page allows you to define the time period after which a filter fault will be generated.

Содержание VESDA-E VEP-A00














































































































Результаты поиска

Содержание VESDA-E VEP-A00

Отзывы:

Похожие инструкции для VESDA-E VEP-A00

Бренды по названию

Популярные бренды

Xtrails VESDA-E VEP-A00, Руководство по эксплуатации продукта

Результаты поиска

Содержание VESDA-E VEP-A00

Отзывы:

Похожие инструкции для VESDA-E VEP-A00

Бренды по названию

Популярные бренды