Xtrails VESDA-E VEP-A00 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 109

background image

VESDA-E VEP-A00-P Product Guide

34

www.xtralis.com

Power to Multiple Detectors

Up to three VESDA-E VEP or VEU detectors may be daisy chained to the same power supply by connecting
the PWR OUT power passthrough socket to the PWR IN socket on each subsequent detector.

Detector 1

Detector 2

Detector 3

PWR IN

PWR OUT

+

+

_

_

PWR IN

PWR OUT

+

+

_

_

PWR IN

PWR OUT

+

+

_

_

PSU

Figure 4-34: Multiple Detectors powered by a single power supply

Compliance

It is recommended that the power supply be compliant with local codes and standards required by the regional
authority. For code-specific information, refer to Codes and Standards Information for Air Sampling Smoke
Detection on page iii.

4.3.4

Communication Ports

The front door must be opened in order to access the communication ports. Refer to Section 7.2 for
information on opening the front door and Figure 4-33 for the physical location of the ports.

Note:

For all connection methods the detector also provides a gateway to all the other devices on the
VESDAnet network.

USB

The USB port is used for initial configuration and local maintenance or servicing of the VEP-A00 using a PC
installed with Xtralis VSC software.

Install Xtralis VSC prior to connecting the VEP-A00 to the PC or Laptop. This ensures that the required
USB drivers are present.

Notes:

l

The USB port must not be used for permanent field connection. For example, do not use a USB to
Ethernet adaptor to connect the detector to a LAN using USB.

l

Refer to the Xtralis VSC documentation for operating system compatibility information.

Ethernet

The Ethernet port is used for permanent network connection to the VEP-A00. An Ethernet lead can be routed
through the cable entry ports and plugged into the Ethernet port.

Use a standard Ethernet lead when connecting the VEP-A00 to a network switch, router or directly to a PC or
laptop.

4.3.5

VESDAnet

VESDAnet is a bidirectional data communication network between connected VESDA-E devices. VESDAnet
connectivity is available on the VEP-A00 detector. Refer to Section 2.6 for further information.

It is recommended that RS 485 (Belden 9841 - 120 Ohm) twisted pair cables be used for including the devices
in the network.

The network cables are terminated at the VESDAnet A and B Terminals. Cabling from one VESDA-E device
is brought into the detector at one terminal and looped out to another device on VESDAnet from the other
terminal.

Notes:

l

The polarity of the data wires must be maintained throughout the network.

l

In order for the detector to be able to detect ground faults on the VESDAnet wiring, the Ground Reference
Terminal (Figure 1-1) must be connected to the local ground.

«
...
40
41
42
43
44
...
»

Содержание VESDA-E VEP-A00














































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VEP-A00

Бренд: Clifford Страницы: 53

Бренд: Climax Technology Страницы: 3

Бренд: jablotron Страницы: 2

Бренд: SkyScan Страницы: 7

30 Lb. Country Smokehouse

Бренд: Sausace Maker Страницы: 12

Бренд: IKEA Страницы: 8

Бренд: Audiovox Electronics Страницы: 12

Бренд: Stronghold Страницы: 2

Бренд: Ambient Weather Страницы: 12

Бренд: La Crosse Страницы: 2

Бренд: La Crosse Technology Страницы: 2

Бренд: olympia electronics Страницы: 2

Бренд: La Crosse Technology Страницы: 4

Бренд: B52 Страницы: 29

Бренд: Hama Страницы: 68

Бренд: Abus Страницы: 177

Бренд: Hannlomax Страницы: 10

Бренд: LaserLine Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды