manualshive.com logo in svg

Xtool D9EV, Руководство пользователя, Страница: 7 / 47

Поделиться
Скачать
Xtool D9EV Скачать руководство пользователя страница 7

5

VEHICLE CONNECTION

WIFI CONNECTION

The WIFI connection method is shown in the figure below:

The scan tool must be connected to the vehicle’s OBD-II port so that the tablet can establish correct vehicle

communication. Please perform the following steps:

1

Turn on the tablet

2

Connect VCI with Vehicle via main test cable and OBD adapter, make sure WIFI connection works fine

3

Switch on the ignition and tap on the Diagnostic application to start your diagnosis.

⚠

Note: The vehicle’s DLC is not always located under the dash; for the location of the DLC, please refer to

the vehicle owner’s manual. Some older vehicles are not compatible with the OBD

Ⅱ

-16 adapter, please make

sure you’re using the correct adapter.

WIRED CONNECTION

When using functions such as ECU programming & coding, please use the USB 3.0 to TYPE-B main cable to connect the

tablet to the VCI box to prevent the failure of function execution due to unstable data transmission and thus any other

damage.

Содержание D9EV
















































Отзывы:

Нет отзывов