XTA DPA SERIES Скачать руководство пользователя страница 40

Страница: 40 / 78

Page 40

DPA Series — DPA80/DPA100 Operating Instructions

Changing Network Output Source cntd…

Amp Matrix

Source



: audio is sourced just after the auxiliary output’s routing matrix (so will

share the same audio feeds) but before all output processing.

Aux Matrix

Source



: audio is sourced just after the amplifier output’s routing matrix (so will

share the same audio feeds) but before all output processing.

Amp M

Source



: audio is sourced just after all amplifier output’s processing

post-mute so

the network copies will be affected by local (or remote) mutes.

Aux M

Source



: audio is sourced just after all auxiliary output’s processing

post-mute so

the network copies will be affected by local (or remote) mutes.

Press ENTER to confirm the changes and exit to the home screens.

PROG. - LIMITERS - PEAK

MUTE

PEQ x 8

DELAY

DYNAMIC EQ x 3

GAIN

PROG. - LIMITERS - PEAK

MUTE

POWER
AMP

AUXILIARY
OUTPUTS [XLR]

SPEAKER
OUTPUTS

MUTE

PEQ x 9

FIR

DELAY

HPF - XOVER - LPF

GAIN

PEQ x 9

FIR

DELAY

HPF - XOVER - LPF

GAIN

POLARITY

INPUT PROCESSING CHANNELS A-D

OUTPUT CHANNELS 1-4 (POWER AMPLIFIER CHANNELS)

AUX CHANNELS 1-4 (XLR OUTPUT CHANNELS)

Содержание DPA SERIES















































































Результаты поиска

Содержание DPA SERIES

Отзывы:

Похожие инструкции для DPA SERIES

Бренды по названию

Популярные бренды

XTA DPA SERIES, Руководство оператора

Результаты поиска

Содержание DPA SERIES

Отзывы:

Похожие инструкции для DPA SERIES

Бренды по названию

Популярные бренды