background image

20

VIDEO TECH TIP

HOW TO BUILD CENTER 

SHOCK

4. SHOCK ABSORBER

971022

O 2x2

Gently push the shock shaft 

completely  into  the  shock 

body.  Excess  oil  will  flow 

through  the  hole  in  the 

shock cap.

Keep  the  shock  shaft 

pushed  in  the  shock  body 

and tighten the shock cap 

completely. 

Tighten  the  cap  fully  but 

do  not  overtighten  or  the 

rubber membrane may be 

damaged.  Make  sure  that 

there  is  no  oil  leakage 

after the cap is tightened.

HALF TIGHTEN

TIGHTEN FULLY

100%

Extend  the  shock  shaft 

completely.  Fill  the  shock 

body with the shock oil. 

Move the shock shaft up and 

down a few times to release 

the  air  bubbles  trapped 

beneath the piston.

Orient  the  filled  shock 

vertically  for  several 

minutes  with  the  shock 

shaft  fully  extended.  The 

remaining air bubbles will 

release.

Install 

the 

shock 

membrane into the groove 

in the upper shock cap.

Gently place the shock cap 

assembly  onto  the  filled 

shock  body.  Excess  oil  will 

spill from the shock. Screw 

the shock cap onto the body 

by only a few turns, approx. 

50%.  Excess  oil  will  flow 

through  the  hole  in  the 

shock cap.

3~5x

UP & DOWN

50%

Follow the steps below to set the shock.

Oil 

700cSt

DEFAULT SHOCK SETTING FOR CENTER SHOCK ABSORBER

Shock Oil

OIL

Shock Oil

OIL

Содержание X10 Link































Отзывы: