Xray T2008, Инструкция по эксплуатации

Страница: 16 / 32

16
901302
SB M3x2.5
981210
P 2x10
DRIVE SHAFTS
#305323 US FOAM-SPEC - 50MM
#305324 EU RUBBER-SPEC - 52MM
1.5MM ALLEN
WRENCH
4x
902310
305324 (EU RUBBER-SPEC)
305323 (US FOAM-SPEC)
902205
901304
303411
901303
303431
302486 (EU RUBBER-SPEC)
302484 (US FOAM-SPEC)
303411
902306
303454
901308
303454
305340
305350
940510
981210
902310
307455
307221
901302
305231
302291
901304
902310
302663
303210
303032
902205
305350
302663
307455
902310 (EU RUBBER-SPEC)
902314 (US FOAM-SPEC) 303210
303032
307321
303454
901308
303454
303431
901303
303484
303411
902310
901304
303411
902306
REAR ANTI-ROLL BAR INCLUDED
ONLY IN EU RUBBER-SPEC KITS
302252 (EU RUBBER-SPEC)
302253 (US FOAM-SPEC)
302364 (EU RUBBER-SPEC)
302374 (US FOAM-SPEC)
302363 (EU RUBBER-SPEC)
302373 (US FOAM-SPEC)
901304
303352 (EU RUBBER-SPEC)
303363 (US FOAM-SPEC)
902314
307455
303352 (EU RUBBER-SPEC)
303353 (US FOAM-SPEC)
305324 (EU RUBBER-SPEC)
305323 (US FOAM-SPEC)
305340
! IMPORTANT
DO NOT use the plastic caps with
the composite ball diffs or composite
solid axle included in the kits.
The new #305241 3.5mm plastic
caps are for use ONLY with ALU ball
diffs or the XRAY Multi-Diff™.
303122
303123
THREAD
LOCK
GRAPHITE GREASE
(HUDY #106210)
TL
TIP
For easy and comfortable installation of the
#305241 plastic caps use pliers as shown.
DO NOT
OVERTIGHTEN
302664
Drive shafts may be combined. For example, you may
use the longer 52mm shafts in the US Foam-Spec edition,
and the standard 50mm shafts in the EU Rubber-Spec
edition. However, we recommend using the drive shafts
that are included in the kit since the drive shaft lengths
have been carefully chosen to optimize speed and ease
of driving.
Longer drive shafts (52mm) make the car easier to drive
because they give more traction and better stability,
mainly in chicanes. However, car will understeer more
than with shorter (50mm) shafts which give a lot of
steering and impart aggression to the car. You may also
combine different lengths of shafts in front and rear (for
example, using long shafts in the rear and short shafts in
the front) depending on track conditions.
Both left & right shafts should ALWAYS be the same length
at one end of the car (front or rear).
BAG
5. FRONT & REAR TRANSMISSION
04
30 2252 T2 COMPOSITE STEERING BLOCK - MEDIUM - RUBBER-SPEC
30 2253 T2 COMPOSITE STEERING BLOCK - HARD - FOAM-SPEC
30 2291 T2 STEEL STEERING BUSHING (2+2)
30 2363 T2 COMPOSITE C-HUB RIGHT - 4° DEG. - MEDIUM - RUBBER-SPEC
30 2364 T2 COMPOSITE C-HUB LEFT - 4° DEG. - MEDIUM - RUBBER-SPEC
30 2373 T2 COMPOSITE C-HUB RIGHT - 4° DEG. - HARD - FOAM-SPEC
30 2374 T2 COMPOSITE C-HUB LEFT - 4° DEG. - HARD - FOAM-SPEC
30 2484 T2 ANTI-ROLL BAR FRONT 1.4 MM
30 2486 T2 ANTI-ROLL BAR FRONT 1.6 MM
30 2663 T2 BALL JOINT 5 MM - OPEN (8)
30 2664 T2 BALL JOINT 5 MM UNIDIRECTIONAL - OPEN (4)
30 3032 T2 ALU QUICK ROLL-CENTER HOLDER™ 4.9MM (2)
30 3122 ALU SHIM 3x6x1.0MM (10)
30 3123 ALU SHIM 3x6x2.0MM (10)
30 3210 TURNBUCKLE L/R 25 MM - HUDY SPRING STEEL (2)
30 3352 T2 UPRIGHT 0° OUTBOARD TOE-IN - MEDIUM - RUBBER-SPEC
30 3353 T2 UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - HARD - FOAM-SPEC
30 3363 T2 UPRIGHT 1° OUTBOARD TOE-IN - LEFT - HARD - FOAM-SPEC
30 3411 T2 COMPOSITE ANTI-ROLL BAR HOLDERS
30 3431 T2 ALU 5 MM BALL END (2)
30 3454 T2 BALL JOINT 5 MM - OPEN (4)
30 3484 T2 ANTI-ROLL BAR REAR 1.4 MM
30 5231 T2 DRIVE SHAFT COUPLING - HUDY SPRING STEEL
30 5323 T2 DRIVE SHAFT 50MM - HUDY SPRING STEEL
30 5324 T2‘008 DRIVE SHAFT 52MM - HUDY SPRING STEEL
30 5340 T2 DRIVE AXLE - HUDY SPRING STEEL
30 5350 T2 ALU WHEEL HUB (2)
30 7221 T2 FRONT ARM PIVOT PIN (2)
30 7321 T2 REAR ARM PIVOT PIN (2)
30 7455 T2 PIVOT BALL 5.0 MM DOUBLE BEVEL SHOULDERS (10)
90 1302
HEX SCREW SB M3x2.5 (10)
90 1303 HEX SCREW SB M3x3 (10)
90 1304 HEX SCREW SB M3x4 (10)
90 1308 HEX SCREW SB M3x8 (10)
90 2205 HEX SCREW SH M2x5 (10)
90 2306 HEX SCREW SH M3x6 (10)
90 2310 HEX SCREW SH M3x10 (10)
90 2314 HEX SCREW SH M3x14 (10)
94 0510 HIGH-SPEED BALL-BEARING 5x10x4 RUBBER SEALED (2)
98 1210 PIN 2x10 (10)