Xray T1R Racer Скачать руководство пользователя страница 23

IMPORTANT NOTES:

• This product is not suitable for children except under the direct supervision

of an adult.

• Carefully read all manufacturers warnings and cautions for any parts used in

the construction and use of your model.

• Assemble this kit only in places away from the reach of very small children.
• First-time builders should seek advice from people who have building

experience in order to assemble the model correctly and to allow the model 
to reach its performance potential.

• Exercise care when using tools and sharp instruments.
• Take care when building; some parts may have sharp edges. Keep small

parts out of reach of small children.

• Do not put fingers or any objects inside rotating or moving parts.
• Right after using your model, do NOT touch equipment on the model

because they may generate high temperatures.

• Be sure that your operating frequency is clear before running and never

share the same frequency with somebody else at the same time.

• Always turn on your transmitter before you turn on the receiver/speed

controller or connect the battery pack. Always turn off the receiver/speed
controller or disconnect the battery pack before turning your transmitter off.

• Disconnect the battery pack before storing your model.
• When learning to operate your model, go to an area that has no obstacles

that can damage your model if you crash.

• Remove any sand, mud, dirt, grass or water before putting your model away.
• Use a recommended charger for the batteries and follow the instructions

correctly. Over-charging, incorrect charging, or using inferior chargers can
cause the batteries pack to become dangerously hot.

• Do not allow the transmitter batteries to run low, otherwise you risk losing

control of the model.

• Regularly check the charger for potential hazards such as damage to the cable,

plug, casing or other defects. Ensure that any damage is rectified before using
the charger again.

• Do not allow any metal part to short circuit the batteries or speed control.
• If the model behaves strangely, immediately stop the model and check and clear

the problem.

• Do not stall the motor. The speed control will fail within seconds if power is

applied to the motor when the car cannot move.

• The composite material is sensitive to very high temperatures. Prolonged

exposure to very high temperatures will damage the composite and may cause it
to deform. For example, do not leave the T1R in a sealed car during hot days.

• Do not use your model:

- Near real cars, animals, or people that are unaware that an R/C car 

is being driven.

- In places where children and people gather
- In residential districts and parks
- In limited indoor spaces
- In wet conditions
- In the street

TTaakkee  aaddeeqquuaattee  ssaaffeettyy  pprreeccaauuttiioonnss  pprriioorr  ttoo  ooppeerraattiinngg  tthhiiss  m

mooddeell..

YYoouu  aarree  rreessppoonnssiibbllee  ffoorr  tthhiiss  m

mooddeell''ss  aasssseem

mbbllyy  aanndd  ssaaffee  ooppeerraattiioonn..

D

Diissrreeggaarrdd  ooff  tthhee  aannyy  ooff  tthhee  aabboovvee  ccaauuttiioonnss  m

maayy  lleeaadd  ttoo  aacccciiddeennttss,,  ppeerrssoonnaall

iinnjjuurryy,,  oorr  pprrooppeerrttyy  ddaam

maaggee..

XXRRA

AYY  M

MO

OD

DEELL  RRA

AC

CIIN

NG

G  C

CA

ARRSS  aassssuum

meess  nnoo  rreessppoonnssiibbiilliittyy  ffoorr  aannyy  iinnjjuurryy,,  ddaam

maaggee,,

oorr  m

miissuussee  ooff  tthhiiss  pprroodduucctt  dduurriinngg  aasssseem

mbbllyy  oorr  ooppeerraattiioonn..

22

C

Coonnggrraattuullaattiioonnss,,  yyoouurr  nneew

w  XXRRA

AYY  TT1

1  RRaayycceerr  m

mooddeell  rraacciinngg  ccaarr  iiss  nnoow

w  ffiinniisshheedd..

PPrroocceeeedd  ttoo  tthhee  SSeett--U

Upp  BBooookk  ttoo  lleeaarrnn  aabboouutt  aaddjjuussttiinngg  tthhee  ssuussppeennssiioonn  ggeeoom

meettrryy..

Содержание T1R Racer

























Отзывы: