background image

OTHER INSTRUCTIONS

Installing Wheels & Track-width Adjustment
If you remove the wheels from the car, reinstall the wheels by pushing the white outer wheels onto the black inner wheel adaptors. Push the outer white 
wheels until the tabs seat all the way on the inner wheel.

Each inner wheel adaptor has 3 short and 3 long slots to enable the track-width adjustment. The short slots give a wider track-width adjustment, while 
the long slots give a narrower track-width adjustment. When installing wheels at one end of the car (front or rear), make sure to install both left and right 
wheels using the same slots (short or long). 

A

B

GLUING THE TIRES

The tires on your M18 are pre-glued and for the quick start you can skip this section.

If you will purchase a new set of tires, you must glue the tires on your M18 (using CA glue) to prevent the tires from spinning on the wheels. You can glue 
the tires with or without removing the wheels from the car.

1.  To remove the wheel, gently squeeze (pinch) the tire/wheel while pulling off from the inner wheel adaptor.
2.  Using your thumb, push the edge of the tire away from the wheel so there is a gap. 
3.  Place a one or two of CA glue into the gap and release the tire. Capillary action will draw the glue around the bead of the tire. 
4.  Apply CA glue to 5 or 6 spots around the wheel until the tire is completely glued to the wheel. 
5.  Turn the wheel over and repeat the process for the inside of the wheel/tire. 
6.  Repeat for the remaining wheels.

PUSH WHEEL TABS ALL THE WAY 
INTO THE SLOTS ON THE INNER 
WHEEL

PLACE BRAKE DISC DECAL ON 
INNER WHEELS

FRONT     98mm    101mm

REAR       104mm   107mm

A

B

A

B

A

B TRACKWIDTH (WIDE)

A TRACKWIDTH (NARROW)

CA

FRONT TIRES - LARGER

NO SPACE

NOTE
ORIENTATION

!!! Always wear safety glasses and gloves to prevent CA glue from splattering into your eyes or 
onto your hands and skin. !!!

REAR TIRES - SMALLER

11

Содержание M18 PRO


















Отзывы: