Xpresskit Canmax Series Скачать руководство пользователя страница 5

Страница: 5 / 6

Page 5 to 6

Module Programming

TWO Valid Keys Required to program

Max 5 second intervals between each step. If 5 seconds is exceeded, vehicle will exit “on board”
programming and you must restart.

Insert 1st valid Ign. key & turn to “ON” position until security light turns off. Remove 1st valid key. Within 5 secs.

Insert 2nd valid Ign. key & turn to “ON” position until security light turns off. Remove 2nd valid key. Within 5 secs.

3) - Automatic vehicle:

Press & hold the programming button and then remote start the vehicle with the transmitter.

(keep holding the programming button)

- Manual vehicle:

Press & hold the programming button and then ap12v to the vehicle’s ignition wire with

a jumper wire. (keep holding the programming button)

Green LED comes ON for 3 seconds and shuts off.

Release the programming button & remove the jumper wire if applicable.

TESTING:

Wait (2) minutes after programming then start engine by valid ignition key.
Stop engine & remove key then remote start.

TROUBLESHOOTING:
A)

If LED stays on solid or flashes rapidly, reverse the TX and RX wire connections.

If module fails to program or module was previously used on another vehicle then RESET the Module.

Max 5 second intervals between each step. If 5 seconds is exceeded, vehicle will exit “on board
programming and you must restart.

Insert 1st valid Ign. key & turn to “ON” position until security light turns off. Remove 1st valid key. Within 5 secs.

Insert 2nd valid Ign. key & turn to “ON” position until security light turns off. Remove 2nd valid key. Within 5 secs.

Remote start the car with the transmitter.

Green LED comes ON for 3 seconds and shuts off. Release the programming button.

TESTING:

Wait (2) minutes after programming then start engine by valid ign. key. Stop engine & remove key then remote start.

TROUBLESHOOTING:
A)

If LED stays on solid or flashes rapidly, reverse the TX and RX wire connections.

If module fails to program or module was previously used on another vehicle then RESET the Module.

Reset Module

Disconnect the module from any power source.

Press and HOLD the integrated programming button.

onnect the module to the power source

Wait until the orange LED turns ON (should be 3 seconds)

Release the integrated programming button.

Reset is done.

While holding integrated programming button, c

Please Note:

Jumper

position

When a CANMAX400 is used in D2D with either Viper

™

, Clifford

™

or Python

™

the jumpers on the remote starter

MUST

be placed in the

Horizontal

position.

INSTALLATION GUIDE

MODEL: CANMAX400
FIRMWARE: FORD1

Rev.: 20091005

Vehicle Integration Canbus System

Can Low: Fils torsadé Blanc

Can High: Fils torsadé Blanc/Orange

(Kick Pad Chauffeur mais pas sûre)

CHRYSLER

300/300C

Aspen

PT Cruiser

Sebring Convertible

Sebring Sedan

DODGE

Avenger

Caliber

Charger

Dakota

Durango

Magnum

RAM

JEEP

Commander

Compass

Grand Cherokee

Patriot

)

-O

)

-B

Vehicle Years & Installation Type*

Содержание Canmax Series







Результаты поиска

Содержание Canmax Series

Отзывы:

Похожие инструкции для Canmax Series

Бренды по названию

Популярные бренды

Xpresskit Canmax Series, Руководство по установке

Результаты поиска

Содержание Canmax Series

Отзывы:

Похожие инструкции для Canmax Series

Бренды по названию

Популярные бренды