background image

© XPAND, All Rights Reserved. 

 

www.xpandvision.com

5. Stereoscopic viewing may cause a slight after-effect in vision.
Your eyes change to accommodate viewing through 3D glasses. Wait a few moments after you remove the 3D glasses for your eyesight to 
return to normal before resuming your regular activities.
6. Do not use 3D glasses for purposes other than viewing 3D visual content.
Do not wear 3D Glasses as sunglasses or safety glasses. Never wear 3D glasses while driving, swimming, or operating machinery. Do not 
use near staircases, ledges or balconies. You may risk falling during or after use.

Regulatory Compliance Statements

Caution: Any changes or modifications to this equipment not explicitly approved by X6D Limited shall void the user’s authority to operate it.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Hereby X6D Limited declares that the MS210C2 is in compliance with the essential requirements and other relevant provisions of the 
EU Directive 2004/108/EC. The declaration of conformity may be consulted at http://www.xpandvision.com/products/xpand-passive-3D-
polarization-modulator/declaration-of-conformity/

Copyright

The contents stated herein are the property of X6D Ltd.. All rights reserved. Any unauthorized copy, reproduction, distribution, publication, 
display, modification, transmission or quoting of any part of this manual is strictly prohibited and will be prosecuted to the maximum extent 
possible.

UMA5-V2-ENG

Содержание MS210C2





















Отзывы: