XMODUS AL5068S Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 46

background image

XM1240S AT Command Reference Manual

No. XM1240S-A00-106

xmodus swiss GmbH

5 / 46

1. INTRODUCTION

1.1 OVERVIEW

This manual describes the AT Commands and the S-Registers for the following
xmodus Socket Modem families:

AL5068S

ISDN Socket Modem (5V Version)

AL5068S-3V

ISDN Socket Modem (3V Version)

AL5068SI-3V

ISDN Socket Modem (3V Version and IOM-2 bus)

The description apply to all these isdn-modems with any differences between product
families noted. Refer to Modem Firmware Release notes for commands applicable to
modem firmware.

1.2 PRODUCT

DESCRIPTION

The xmodus AL5068S, AL5068S-3V and AL5068SI Socket Modem Family provides
the OEM with a complete ISDN data/voice/speakerphone modem in a compact
socket-mountable module. This modules enables any devices to send and receive
data over the ISDN network. The European EuroISDN DSS-1 ISDN network is
supported. The module is fully approved and homologated and conforms to the CE
regulations. This gives fastest time-to-market to ISDN-enable any devices.

The compact size and high level of integration of the Socket Modem minimizes real
estate and cost for motherboard and box modem applications. Its low power
consumption makes it ideal for a wide variety of embedded control applications. The
pin compatibility between the full range of Analog Series Socket Modems, ISDN and
GSM Socket Modems allows upgrading and production configurability without
hardware changes.

As a data modem, the AL5068S Socket Modem can send and receive data at speeds
up to 64kbps and 128kbps in the 2-channel version. B-Channel protocols such as
V.110, V.120, PPP, transparent and X.75 are supported.

For X.25 networks, X.31 Case A and X.31 Case B (D- and B-channel) is supported.
The integrated X.3 PAD can be used for data transfer to the X.25 network.

The AL5068SI-3V Socket Modem supports Voice features. By adding two external
PCM Codecs the modem supports two independent analog voice ports. Digital voice
transfer is also supported.

All manuals and user guides at all-guides.com

«
...
3
4
5
6
7
...
»

Содержание AL5068S















































Отзывы:

Нет отзывов

Похожие инструкции для AL5068S

Бренд: Yealink Страницы: 12

Бренд: Satel Страницы: 2

Бренд: Novatel Страницы: 74

Бренд: CyberTAN Страницы: 6

Бренд: AirLive Страницы: 77

Бренд: Infiniteq Страницы: 11

Бренд: Zte Страницы: 9

Бренд: 3Com Страницы: 22

INTERNET DSL MODEMS

Бренд: Geetel Страницы: 10

Бренд: FP Страницы: 16

Бренд: Elastic Networks Страницы: 32

Бренд: Electronics Is Fun Страницы: 35

Cable Modem External

Бренд: 3Com Страницы: 62

Бренд: Zte Страницы: 2

Бренд: US Robotics Страницы: 151

Бренд: iFox Страницы: 8

Бренд: Adcon Страницы: 47

Бренд: Alcatel Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды