Xmart OPTIMA-T09W-06K-230V Скачать руководство пользователя страница 25

Страница: 25 / 36

INDEX

USER MANUAL - OPTIMA T09W 6K/10K

www.xmart-ups.com

VER.1801.25-WP+ (ENG)

ALARM & ERROR CODES / TROUBLESHOOTING

IMPORTANT:

▪

All alarm and errors are informed don the LCD by dedicated codes and symbols.

▪

ALARMS: Are usually represented by blinking codes or symbols. Audible alarm beeps are also intermittent for alarms. Alarm

states do not avoid UPS working in ONLINE mode.

▪

ERRORS: Are usually represented by steady codes or symbols. Audible alarm for errors always sounds continuously. Error

states force UPS to go to Static Internal BYPASS mode.

ALARM SYMBOLS AND CODES

ALARM

ALARM SYMBOLS

AUDIBLE BEEP

OVERLOAD detected at UPS output

2 beep / s

LOW BATTERY

1 beep / s

BATTERY DISCONNECTED OR FAULTY

1 beep / s

BATTERY OVER-VOLTAGE

1 beep / s

INPUT FUSES BROKEN

1 beep / s

EMERGENCY POWER-OFF ACTIVATED

1 beep / s

HIGH TEMPERATURE

1 beep / s

CHARGER FAILURE

1 beep / s

* UPS BLOCKED: as consequence of detecting 3 overloads

in less than 30 minutes OR

* MBS cover REMOVED

1 beep / s

ALARMS

ALARM CODES

Battery Disconnected

Battery overvoltage

Los Battery

Overload at UPS output

FAN failure

EPO activated

Over temperature

Charger failure

Internal input fuse broken

Configuration mismatch in ONLINE for parallel (available only for UPS with parallel functionality)

Configuration mismatch in BYPASS for parallel (available only for UPS with parallel functionality)

UPS blocked by 3 consecutives overloads (in less than 30 minutes)

MBS safety plate removed

Input BYPASS unstable

Boot Loader failure

Some errors and alarms could block UPS until problem is solved and UPS unblocked by operator. Operator must be

sure cause of problem has been solved before clear alarm and unblock UPS. Alarm can be deleted by pressing

<UP> and <DOWN> keys at same time, when UPS is in BYPASS mode.

Содержание OPTIMA-T09W-06K-230V





































Результаты поиска

Содержание OPTIMA-T09W-06K-230V

Отзывы:

Похожие инструкции для OPTIMA-T09W-06K-230V

Бренды по названию

Популярные бренды

Xmart OPTIMA-T09W-06K-230V, Руководство пользователя

Результаты поиска

Содержание OPTIMA-T09W-06K-230V

Отзывы:

Похожие инструкции для OPTIMA-T09W-06K-230V

Бренды по названию

Популярные бренды