background image

XL-SEAT

 2005-2011 DODGE DAKOTA CLUB CAB PASSENGER 

p. 9

 

 

 
 
 
 
 
 
 
 

 

TROUBLESHOOTING 

PROBLEM 

POSSIBLE CAUSES 

XL-SEAT 

will not run

 

Bad electrical connections.

 Check and clean corrosion from all 

connections including the car’s battery cable connections.

 

 

Hand  pendant  wire  problem.

  Check  hand  pendant  wire  to 

make sure it is properly plugged. Check the wire for any cuts.  
If so, replace the wire. 
 

Burnt out switch.

 Replace pendant. 

 

Bad connection.

 Check the electronic module under the seat. 

Make sure that all the wires are properly connected. 

 
Burnt  out  electronic  module. 

Contact 

Adapt  Solutions

  for 

replacement module. 

 
Burnt out actuator.

 Replace actuator. 

 
Power  Loss.

  The 

XL-SEAT

  motor  is  not  getting  adequate 

electrical  power  because  of  a  loose  connection.  Check  the 

XL-SEAT

  connections  for  tightness  and  corrosion 

(especially the ground connection). 
 

A partially discharged battery in the vehicle.

  Check the 

car’s 

battery by trying the car lights or checking the voltage with a 
voltmeter (should read 13.2 volts). Clean the car battery posts 
and  cable  clamps  thoroughly  (remove  the  battery  clamps  off 
the battery posts and clean them with a wire brush designed 
for  that  purpose).  Coat  the  connection  with  anticorrosion 
spray once reassembled. An automotive battery may be weak, 
having  enough  power  to  start  the  car  but  not  enough  power 
for continuous use. 

 

Содержание XLS-DAKC05R










Отзывы: