XIMEA xiC Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 117

background image

xiC - Technical Manual Version 1.16

4

1.2.3.

For customers in the US: FCC Conformity

The xiC cameras described in this manual have been tested and found to comply with Part 15 of the FCC rules, which states
that:

Operation is subject to the following two conditions:

•

This device may not cause harmful interference, and

•

This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the
interference at their own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate
this equipment under above jurisdictions. The shielded interface cable recommended in this manual must be used with this
equipment in order to comply with the limits for a computing device pursuant to Subpart J of Part 15 of FCC Rules.
Please refer also to chapter

1.2.4.

For customers in Canada

The xiC cameras comply with the Class A limits for radio noise emissions set out in Radio Interference Regulations.
Please refer also to chapter

1.2.5.

RoHS Conformity

The xiC cameras comply with the requirements of the RoHS (Restriction of Hazardous Substances) Directive
2011/65/EU.

1.2.6.

WEEE Conformity

The xiC cameras comply with the requirements of the WEEE (waste electrical and electronic equipment) Directive
2003/108/EC.

1.2.7.

AIA standard USB3 Vision

The xiC cameras are compliant with the

USB 3.0 SuperSpeed specification

and are designed to be

compliant with the

AIA USB3 Vision standard

1.2.8.

GenICam GenTL API

GenICam standard transport layer interface, grabbing images.

provides an agnostic transport layer interface

to acquire images or other data and to communicate with a device. Each XIMEA camera can be GenTL Producer.

1.2.9.

Camera Sub-Assemblies

The FL and FV camera models are "semi" housed with flex ribbon cable interfaces. As such, these devices do not comply with
CE/FCC/Class A limits (Canada) regulations. The system integrator (customer) is liable for compliance with CE/FCC/ Class A
limits (Canada) regulations.

«
...
2
3
4
5
6
...
»

Содержание xiC






















































































































Отзывы:

Нет отзывов

Похожие инструкции для xiC

Бренд: Olympus Страницы: 127

Бренд: Olympus Страницы: 36

225755 - Stylus 700 7.1MP Digital Camera

Бренд: Olympus Страницы: 86

225690 - Stylus 600 6MP Digital Camera

Бренд: Olympus Страницы: 157

225690 - Stylus 600 6MP Digital Camera

Бренд: Olympus Страницы: 84

FE 115 - Digital Camera - 5.0 Megapixel

Бренд: Olympus Страницы: 110

Бренд: Vacron Страницы: 5

Бренд: Vacron Страницы: 2

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 104

Lumix DMC-GH2EB

Бренд: Panasonic Страницы: 200

Бренд: Panasonic Страницы: 82

ARTCAM-990SWIR-TEC-CL

Бренд: ARTRAY Страницы: 17

Бренд: HuddleCamHD Страницы: 17

Бренд: Pentax Страницы: 212

Luxmedia D00450

Бренд: Praktica Страницы: 1

Бренд: Eborn Страницы: 3

Бренд: Easylife Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды