Xilinx Virtex-5 RocketIO GTP Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 316

background image

Virtex-5 RocketIO GTP Transceiver User Guide

73

UG196 (v1.3) May 25, 2007

Reset

R

Ports and Attributes

defines the shared tile reset ports.

There are no attributes in this section.

Table 5-6:

Shared Tile Reset Ports

Port

Dir

Domain

Description

GTPRESET

In

Async

This port is driven High to start the full GTP_DUAL reset sequence.
This sequence takes about 160

μ

s to complete, and systematically

resets all subcomponents of the GTP_DUAL tile.

RESETDONE0
RESETDONE1

Out

Async

This port goes High when the GTP transceiver has finished reset
and is ready for use. For this signal to work correctly, CLKIN and
all clock inputs on the individual GTP transceiver (TXUSRCLK,
TXUSRCLK2, RXUSRCLK, RXUSRCLK2) must be driven.

RXBUFRESET0

RXBUFRESET1

In

Async

This active-High signal resets the RX buffer logic.

RXCDRRESET0

RXCDRRESET1

In

RXUSRCLK2

Individual reset signal for the RX CDR and the RX part of the PCS
for this channel. This signal is driven High to cause the CDR to give
up its current lock and return to the shared PLL frequency.

RXELECIDLERESET0

RXELECIDLERESET1

In

Async

These active-High reset inputs reset the GTP transceiver receive
logic when the link is in a powerdown state.

these signals are connected. If the link idle reset is not supported,
these signals are strapped Low.

RXENELECIDLERESETB

In

Async

When asserted, this active-Low signal enables the
RXELECIDLERESET0/1 inputs.

shows how this signal is

connected when the link idle reset is supported. If
RXELECIDLERESET0/1 are not used, this signal is strapped High.

RXRESET0

RXRESET1

In

Async

Active-High reset for the RX PCS logic.

TXRESET0

TXRESET1

In

Async

Resets the PCS of the GTP transmitter, including the phase adjust
FIFO, the 8B/10B encoder, and the FPGA TX interface.

PRBSCNTRESET

In

RXUSRCLK2 Resets the PRBS error counter.

PLLPOWERDOWN

In

Async

Powers down the shared PMA PLL. Driving PLLPOWERDOWN
from Low to High triggers a GTPRESET.

«
...
71
72
73
74
75
...
»

Содержание Virtex-5 RocketIO GTP





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 RocketIO GTP

Бренд: Hama Страницы: 24

Бренд: RadioMaster Страницы: 10

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 40

Бренд: Yamaha Страницы: 2

Бренд: EastLink Страницы: 3

Бренд: elero Страницы: 10

Бренд: Radio Shack Страницы: 61

u-blox 8 NL-8001U

Бренд: Navilock Страницы: 11

Бренд: Onkyo Страницы: 285

AN/PRC-117D Series

Бренд: Harris Страницы: 40

Бренд: E+E Elektronik Страницы: 40

Бренд: Onkyo Страницы: 50

Бренд: Harman Kardon Страницы: 12

Бренд: Icom Страницы: 32

Бренд: Wonde Proud Страницы: 11

Бренд: Vectronic Aerospace Страницы: 10

Бренд: Topfield Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды