Xerox Synergix 8850 Скачать руководство пользователя | Manualshive

Страница: 293 / 432

background image

03/2003

6-7

8850/ 510DP

To Exit from Multiple Tests, Special Tests

General Procedures

To Exit from Multiple Tests

Multiple tests can be switched off by two methods.

1.

Enter the codes in the reverse sequence from the way they were initially entered, press-
ing the EXIT button after each code.

2.

Press and hold the DOT (.) button while pressing the EXIT button. This will clear all of the
codes that were entered.

Special Tests

The following tables give special diagnostic tests that are used to enable or disable features or
to change the operating parameters of the Printer. To enter a Special Test, the Printer must
first be in the diagnostic mode

Each special test has a value that is stored in non-volatile memory (NVM). If there is a default
value, it is found in the Value column.

NVM values may be changed by entering the Special Test mode, pressing the ENTER button,
and then using the PREVIOUS and NEXT arrow keys to select the desired NVM value. To
enter the selected value, press the ENTER button again. To exit the test, press the EXIT but-
ton.

NOTE: If there is a reference to a procedure, the procedure must be followed in order to per-
form the test correctly.

Table 1 Special Tests

Code

Description

Value

[0200]

Online Mode

[0211]

Language ROM Test

0 = Both Language ROMs are defec-
tive.
1 = Secondary Language ROM is
defective
4 = Primary Language ROM is defec-
tive
5 = Neither Language ROMs are defec-
tive

[0261]

Maximum Line Current Limit Set
(dependent on service)

US/Canada:

17.6 amps = 220 VAC, 20 amp. service
13.2 amps = 220 VAC, 15 amp. service

EO:

16.0 amps = 230-240 VAC, 16.0 amp.
service

UK:

13.0 amps = 230-240 VAC, 13.0 amp.
service

Switzerland:

10.0 amps = 220 VAC, 10 amp. service
Central and South America:
20.0 amps = 220 - 240 Volts @ 15
amps,

[0263]

Billing Meter Count
This code is used to select the billing
in meters or inches.

NACO: 0 = inch

EO: 1 = metric (meters)

[0300]

Jump 0.

Restarts the IOT.

[0301]

Enter IOT Firmware Update Mode

Download the latest software.

«
...
291
292
293
294
295
...
»

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synergix 8850

Бренд: Xerox Страницы: 2

WorkCentre Pro 40

Бренд: Xerox Страницы: 14

Бренд: Magicard Страницы: 2

Бренд: Magicard Страницы: 2

Бренд: Panasonic Страницы: 240

MP 2554SP Series

Бренд: Ricoh Страницы: 1

Бренд: Geeetech Страницы: 52

Бренд: SAGEMCOM Страницы: 146

Бренд: Xerox Страницы: 2

Бренд: idp Страницы: 63

Бренд: Lanier Страницы: 4

Бренд: Ricoh Страницы: 84

Бренд: Canon Страницы: 76

Past Ethernet Combo Print Server PS-1216U

Бренд: Edimax Страницы: 23

Бренд: Epson Страницы: 157

CardJet X001200

Бренд: FARGO electronics Страницы: 52

Бренд: Xerox Страницы: 203

Бренд: zortrax Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды