Xerox Nuvera Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 294

background image

13

When to unload Stackers

Various stackers are available for use with the Xerox Nuvera. Depending upon the situation, each of
these devices may require that paper be unloaded from the stacking tray. The table below shows each
of these unload situations for the BFM, DS3500/XPS, and the Xerox Production Stacker (XPS).

XPS

DS3500/XPS

BFM

Unload situation

Operator presses the Un-
load button on the finisher

• First or single press

starts the unload pro-
cess (eject), second
press pauses the
eject/raise/lower, third
press resumes
eject/raise/lower lower-
ing.

•

•

First or single press
starts tray lowering,
second pres stops
lowering, third press re-
sumes output tray
lowering, etc.Front door
must be opened/closed
to raise tray & allow
system to go ready

Single press or multiple
presses lowers tray to
unload position. Tray
lowers only enough to
enable BFM output tray
to slide out

or selects Unload on the
UI.

• After the unload is

complete the system
goes ready (continue
printing)

(continue print-
ing)Sheets are not re-
quired to be removed to
allow system to go
ready (continue print-
ing) after door is
opened/closed.(Note:
Paper present sensor is
about 1/4" in from the
Lead Edge.)

Operator opens the front
door while the Xerox
Nuvera is idle and paper is
present in the stacker.

• Opening is allowed.

• Opening is allowed.

• Can not open door

without pressing unload
button (door is inter-
locked)

• Sheets are not required

to be removed to allow
system to go ready
(continue printing) after
door is opened/closed

• Sheets are not required

to be removed to allow
system to go ready
(continue printing) after
door is opened/closed

13-1

Xerox

®

Nuvera

®

User Guide and Training Aid (UGTA)

«
...
119
120
121
122
123
...
»

Содержание Nuvera







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nuvera

Бренд: Canon Страницы: 58

image Prograf iPF680 Series

Бренд: Canon Страницы: 132

Бренд: Canon Страницы: 44

imageClass LBP6230dw

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 2

imageprograf IPF785

Бренд: Canon Страницы: 42

Бренд: Canon Страницы: 148

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 6

Color Bubble Jet BJC-1000 Series

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Color Bubble Jet BJC-8200

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

imagePROGRAF iPF830

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды