Installation Preparation Document
(for physical installation of the product only)
Xerox DocuTech 128/155/180 HighLight Color
701P46159
October 2006
•
50 Hz service
•
30 amp dedicated service (WYE): 220/380 VAC or 230/400
VAC or 240/415 VAC (3 phase)
Agency certifications: UL, cUL, CE Mark, FCC
Electrical Requirements (Controller)
The Controller requires 20 AMP dedicated service. The information
for the 20 Amp electrical service is identified below.
Controller
36 Track Tape
(Optional)
Line Options
Dedicated
Dedicated
Voltage 115vac
115vac
Amperage 20
20
Cycles
60 Hz
60 Hz
Xerox Receptacle Part No.
600S3703
600S3703
Receptacle NEMA Part No.
5-20R
5-20R
Power Cord Xerox Part No.
98K19950
98K19950
Receptacle Diagram
97S02370
97S02370
Installation Considerations
1.
DocuTech HLC printers built in 2004 may require specific
delivery cooperation between the Xerox Service Representative
and the delivering Rigger for any doorway or hall that is smaller
than 37 inches. Please ensure that Xerox Service is informed
during the preinstallation planning process if any opening
through which the printer is to be moved is smaller than 37
inches.
2.
Dedicated service is required for each component.
3.
The controller can be connected to a 15 amp or 20 amp outlet.
4.
The length of the cable from the controller to the printer is 16
feet (4.8 metres).
5.
Do not use an adapter to connect the controller to an electrical
outlet that lacks a ground connection terminal.
6.
The customer is responsible for providing the network and the
client workstation(s). The Ethernet interface on the DocuSP
controller is a auto-sensing 10/100/1000 - MB/sec twisted pair
standard (BaseT).
7.
The Ethernet connection to the DocuSP controller must be
compatible with the Institute of Electrical and Electronics
Engineers (IEEE) 802.3 standard.
Paper Handling
•
16 to 110 lb. (60 to 200 gsm) cut sheet paper weights
•
8 by 10 in. to 14 x 17 in. (203 by 254 mm to 356 by 432 mm)
including A4, A3, and B4 paper sizes
•
7 by 10 in. (178 by 254 mm) optional enablement kit
•
Transparencies, label stock, tab stock, carbonless paper, pre-
perforated stock
•
Paper stock weights less than 16 lb. are not recommended.
•
Textured stocks are not recommended.
•
Some 65 lb. stocks may not fully fuse.
Input
Tray
Capacity
Main tray (tray 1)
1,100 sheets 20 lb (75
gsm)
Auxiliary tray (tray 2)
600 sheets 20 lb (75 gsm)
High capacity feeders (trays 3
and 4)
2,600 sheets each 20 lb
(75 gsm)
Additional high capacity feeders
(up to two optional)
2,600 sheets each 20 lb
(75 gsm)
Output
Tray
Capacity
Two high-capacity stackers
2,500 sheets each 20 lb
(75 gsm)
Sample tray
100 sheets 20 lb (75 gsm)
Purge tray
100 sheets 20 lb (75 gsm)
Environmental Requirements
Temperature
50 to 85
o
F
(10
o
to 29
o
C)
Humidity
Non-condensation
30 to 65% RH
Heat Emission - printer
4454 BTU/Hr
(Standby)
32,770 BTU/Hr
(Operating)
Altitude (above sea level)
Up to 6,000 ft
(1830 m)
Operating Supplies
Reorder No.
Dry Ink - Black
6R206 (US/CA)
Dry Ink – Blue
6R1191 (US/CA)
6R90343 (XE)
Dry Ink – Red
6R1192 (US/CA)
6R90344 (EU)
Dry Ink – Green
6R1193 (US/CA)
6R90345 (EU)
Dry Ink – Royal Blue
6R1255 (US/CA)
6R90356 (XE)
Dry Ink – Cardinal Red
6R1277(US/CA)
6R90358(XE)
Dry Ink – Cyan
6R1284(US/CA)
6R90359(XE)
Dry Ink – Magenta
6R1296 (US/CA)
6R90360 (XE)
Dry Ink – Yellow*
6R1299 (US/CA)
6R90361 (XE)
Developer (Black, Red,
Blue, Green, Royal Blue,
Cardinal Red, Cyan,
Magenta, Yellow)
NA
Fuser Blend
8R12938 (1 bottle)
8R12939 (6 bottles)
Fuser Shield
8R4077 (1 bottle)
8R7618 (6 bottles)
Dry ink waste container
93K1393
HLC developer waste bottle
604K24870 (4 bottles)
* Will be available in the near future
.