Xerox 721 Скачать руководство пользователя страница 66

Страница: 66 / 72

USER MODES

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

User Mode 6 (Detack Lamp Control Mode) “U6”

If the print quality of prints made on Film media lack sharpness or
have a light overall appearance, a Detack Lamp in the print
process can be switched OFF using Mode 6. This action
increases the amount of Toner transferred to the print.

NOTE

: If a higher than normal jam rate is experienced, the Detack

Lamp may have to be switched on again.

1. With the printer in the Standby (idle) condition, press the

[Menu] Key 6 times to enter Mode 6.

The [Menu] Key lights and the display indicates “U6” on the left
side of the display and the current setting on the right side.

2. Press

[Enter]

3. Press the [

→

←

] key to change the value to 0 (OFF)

The value in the display will change to 0 (OFF)

The range is 1 – On and 0 - Off

NOTE: Factory default is “0”, Off.

4. Press the [Online] Key to exit the User Mode.

Enter

Online

Press [Menu] 6 times

Enter

Online

Enter

Online

Enter

Online

Содержание 721









































































Результаты поиска

Содержание 721

Отзывы:

Xerox 721, Руководство оператора, Страница: 66 / 72

Результаты поиска

Содержание 721

Отзывы: